Abstract:As critical load-bearing components of aerospace equipment, thin-walled conical rings with inner transverse ribs (TWCRITR) are widely used for manufacturing rocket body, aircraft fuselage and space station shell et al., due to light weight, high strength and high load-bearing capacity. However, TWCRITR cannot be manufactured by traditional ring rolling (TRR), due to thin skin and high ribs. Aimed at this problem, a novel constraining ring rolling method (CRR) is proposed in this work to achieve the near-net-shape manufacturing of TWCRITR with high performance and efficiency. CRR innovatively uses a constraint roll and two baffles to fully constrain the diameter and height enlargement of ring, which ensures that the CRR process is still stable and the metal is enforced to flow axially to form high and wide ribs. Owing to the extreme geometry of TWCRITR and the complicated constraints of rolls in CRR of TWCRITR, the inherent relation between geometric and process parameters, stress state and metal flow is complicated, and it cannot be quantitatively determined by the FE simulation or experiment. Hence, the mechanical model which can determine the quantitative relation between geometric and process parameters, stress state and metal flow in CRR of TWCRITR is firstly established by using the slab method and upper bound method. Secondly, three new metal flow modes related with rib width in CRR of TWCRITR are found based on the established mechanical model. The first one is that the real-time height difference of two ribs slightly fluctuates and the two ribs almost grow synchronously when the width of two ribs is almost identical. The second one is that the rib with small width at the small end grows much faster than the rib with large width at the large end when the width difference of two ribs exceeds a critical value. The third one is that the rib with small width at the large end grows much faster than the rib with large width at the small end when the width difference of two ribs exceeds a critical value. Further, the quantitative relations between the metal flow resistance, divided-flow plane and rib growth under three metal flow modes are revealed theoretically, and consequently the mechanisms behind three metal flow modes in CRR of TWCRITR are clarified theoretically. Finally, the simulation and experiment for CRR of TWCRITR are conducted, and TWCRITR with 3 mm in skin thickness, 7 mm in rib width and 12.5 mm in rib height (the ratio of rib height to skin thickness is 4.16 and the ratio of rib width to skin thickness is 2.33) are stably rolled. Moreover, the roundness of rolled TWCRITR is good (it nearly approaches the inner surface roundness of constraint roll). The predicted values of rib height using the established mechanical model are in good accordance with the simulated and experimental ones, which validates the established mechanical model. Through analyzing the novel CRR process and complicated metal flow mechanisms, it is demonstrated that CRR is promising for manufacturing TWCRITR with high performance and efficiency.

Multi-pass rolling-extrusion of large-scale thin-walled square tube with longitudinal inner ribs

Rib Filling Behavior in Flow Forming of Thin-Walled Tube with Helical Grid-Stiffened Ribs

Forming dependence on spin roller paths for thin-walled complex components from 2195 Al-Li alloy TWBs

Multi-Mode Damage and Fracture Mechanisms of Thin-Walled Tubular Parts with Cross Inner Ribs Manufactured Via Flow Forming

Research on Bending Forming Method of Large Diameter-Thickness Ratio Thin-Walled Tubes for Aerospace

Innovative Local Shear Forming Method for Enhanced Formability of Tubular Parts with High Stiffened Ribs

Constraining ring rolling of thin-walled conical rings with transverse ribs

Microstructure Evolution of Ti-6Al-2Zr-1Mo-1V Alloy and Its Mechanism in Multi-Pass Flow Forming

Investigation on low hydrostatic stress extrusion technology for forming of large thin-walled components with high ribs

Optimization of Mechanical Properties during Cold Rolling and Wrap-Forming for Metal Helical Tubes

Deformation Characteristics of Transitional Region During Local Loading Forming of Ti-alloy Rib-Web Component on the Double-Action Press

Sheet Metal Forging Process for Thin-Walled Structures with Crossed Ribs: Process Design, Simulation and a Forming Experiment

Numerical and experimental investigation on precision forming of ribbed tube by cold drawing process

Process Design of Flow Control Forming for Rib–web Structure

An innovative radial envelope forming method for manufacturing thin-walled cylindrical ring with inner web ribs

Rolling of Cylindrical Parts with External Cross Ribs

Advances in Spinning of Aluminum Alloy Large-Sized Complicated Thin-Walled Shells

Modeling and Simulation of Tubular Form-Fit Joint Forming by Internal Rolling

Study on generating rolling method for manufacturing cylindrical parts with external cross ribs

Multi-pass Spinning of Thin-Walled Tubular Part with Longitudinal Inner Ribs