Abstract:The recovery of short fibre and epoxy resin from glass fibre-reinforced epoxy resin composites (GFRP) poses a major challenge to the waste recycling sector. These challenges grow when GFRP is mixed with other additives such as carbon nanotubes (CNTs), graphene (GA), and carbon black particles (CB). However, the complexity in terms of activation energy ( E a ) can be decreased through involvement of ZSM-5 zeolite catalyst in the pyrolysis process to convert resin component into chemical and energy products. Within this context, this research aims to study the catalytic pyrolysis of GFRP mixed with three fillers with different structures and dimensions (nanofillers "CNTs, GA" and micro-filler "CB") over zeolite catalyst, where these fillers can be used alongside zeolite particles as hybrid catalysts during the thermal conversion process. The GFRP mixed with different filler panels were prepared in the laboratory using a vacuum-assisted resin transfer method, then they were ground to fine particles and mixed with 200 mass% of ZSM-5 catalyst to prepare them for thermochemical experiments using thermogravimetry (TGA) at 5–30 °C min −1 . The effect of various hybrids on the formulated pyrolysis vapours was studied using TG-FTIR and GC–Ms measurements. The kinetic E a of each batch was studied using three linear isoconversional methods and two nonlinear isoconversional methods to investigate their effect on the decomposition mechanism. Besides, their thermochemical decomposition curves (TGA-DTG) were numerically simulated using DAEM and IPR models. The FTIR and GC analyses revealed that the hybrid catalyst had enhanced formation of aliphatic compounds and phenol compound in case of nanofillers up to 54% (CNTs) and 57% (GA), hence improving them by 17 and 54%, respectively. Meanwhile, the kinetic analysis showed that hybrid catalysts can contribute to a significant reduction in E a up to 158 kJ mol −1 (CNTs), 127 kJ mol −1 (GA), and 124 kJ mol −1 (CB), which means that the decomposition of GFRP, becomes easier and requires less energy. Also, the simulated and experimental results showed big consistency in terms of smaller reaction complexity and higher generation of volatile compounds with increasing heating rates and addition of hybrid catalysts.

Recycling Technology for Waste Glass Fiber Reinforced Plastics (GFRP) Using Pyrolysis with NaOH

Recycling of Waste Glass Fiber Reinforced Plastics (GFRP) via Pyrolysis with Sodium Hydroxide using Microwave Heating

Particle Agglomeration and Inhibition Method in the Fluidized Pyrolysis Reaction of Waste Resin

Recovery of gaseous fuels through CO 2 -mediated pyrolysis of thermosetting polymer waste

Recovery of carbon fiber from Carbon Fiber Reinforced Polymer waste via microwave molten-carbonate pyrolysis

Study on Recycling Carbon Fibers from Carbon Fiber Reinforced Polymer Waste by Microwave Molten Salt Pyrolysis

Research on a two-step pyrolysis-oxidation process of carbon fiber-reinforced epoxy resin-based composites and analysis of product properties

Recycling Glass Fiber from Polyurethane Composite by Pyrolysis Strategy with High Mechanical Properties

From Automotive Shredder Residue to Nano-Ceramics and Graphitic Carbon—thermal Degradation Kinetics

Progress of Research on Chemical Upcycling of Plastic Waste Based on Pyrolysis

Collaborative Disposal of Exhaust Gases and Wasted Wind Turbine Blades: Mechanical Properties of Recycled Glass Fibres and Economic Analysis

Recycling of fiber reinforced composites: Online mass spectrometric tracing, offline physicochemical speciation and toxicological evaluation of a pilot plant pyrolytic conversion

Valorisation of Sub-Products from Pyrolysis of Carbon Fibre-Reinforced Plastic Waste: Catalytic Recovery of Chemicals from Liquid and Gas Phases

Porous Glass Microspheres from Alkali-Activated Fiber Glass Waste

Effect of Glass Fiber-Reinforced Plastic Waste on the Mechanical Properties of Concrete and Evaluation of Its Feasibility for Reuse in Concrete Applications

Thermal decomposition of CNTs and graphene-reinforced glass fibers/epoxy and their kinetics

Thermal Regeneration and Reuse of Carbon and Glass Fibers from Waste Composites

Syngas production through CO 2 -mediated pyrolysis of polyoxymethylene

The pyrolysis of end-of-life wind turbine blades under different atmospheres and their effects on the recovered glass fibers

Catalytic pyrolysis and kinetic study of glass fibre-reinforced epoxy resin over CNTs, graphene and carbon black particles/ZSM-5 zeolite hybrid catalysts

Recovering high-quality glass fibers from end-of-life wind turbine blades through swelling-assisted low-temperature pyrolysis