Abstract:The thermal conversion of waste plastic products can provide a promising solution to the issues of environmental pollution, waste management, and energy needs. However, our present understanding on the thermal reforming of different kinds of plastic wastes mixtures during their co-pyrolysis and co-gasification for syngas production and energy recovery is insufficient. Non-selective urban polypropylene (PP) and polystyrene (PS) waste plastics were chosen for the investigations reported here. Thermal degradation properties of PP and PS as well as their blends in different mass ratios were investigated via thermogravimetric (TG) analysis. Co-pyrolysis and CO 2 -assisted co-gasification of PP-PS blends were then conducted using a fixed-bed reactor at a temperature of 1173 K. Experimental results from the blends were then compared with the weighted value calculated from their component feedstocks to quantify the degree of synergistic effect. TG results showed that the co-treatment of PP and PS enhanced the respective devolatilization process. The co-pyrolysis of PP and PS enhanced their thermal cracking, leading to synergistic increases in the yields of H 2 , light hydrocarbons (HC) and total syngas. In co-gasification, the reforming reaction involving CO 2 was synergistically enhanced, resulting in the increased yields of H 2 and HC. The gasification reactivity of carbon black improved during the co-processing of PP and PS due to the synergistic effect between the two different kinds of plastics. Higher synergistic effects were observed from the plastic mixtures having higher PS content that resulted in increased yield of syngas. Co-gasification of PP-PS blends having 40% PP content (2P3S) exhibited the maximum synergistic effect on H 2 , CO, and total syngas showing increased yields by 88.8%, 77.7%, and 74.2% respectively. The lowest synergistic effect was observed for HC that showed increased yield of only 25.1%. The optimal CO 2 consumption was also observed from the co-gasification of 2P3S. Each gram of 2P3S feedstock consumed approximately 1.80 g of CO 2 to result in highest recovered energy of 27.49 kJ/g and the maximum overall energy efficiency of 43.2%. The results revealed that enhanced thermal cracking and CO 2 reforming reaction, along with the improved reactivity of carbon black were mainly responsible for increased yields of H 2 , HC, CO and total syngas during co-gasification. This study contributes to the fundamental understanding of co-processing of non-separated waste plastics for enhanced syngas production and energy recovery, elucidating the synergistic effect between the various kinds of plastics during their co-pyrolysis and co-gasification.

Syngas production through CO 2 -mediated pyrolysis of polyoxymethylene

Recovery of gaseous fuels through CO 2 -mediated pyrolysis of thermosetting polymer waste

Synergistic effects of CO2 on complete thermal degradation of plastic waste mixture through a catalytic pyrolysis platform: A case study of disposable diaper

Disposal of plastic mulching film through CO2-assisted catalytic pyrolysis as a strategic means for microplastic mitigation

Strategic management of harmful chemicals produced from pyrolysis of plastic cup waste using CO2 as a reaction medium

Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene

Controlling the compositional matrix of pyrogenic products using carbon dioxide in the pyrolysis of agricultural plastic waste

Virtuous utilization of carbon dioxide in pyrolysis of polylactic acid

Production of C5-C12 olefins by catalytic pyrolysis of low-density polyethylene with MCM-41 in CO2/N2

Valorization of synthetic textile waste using CO2 as a raw material in the catalytic pyrolysis process

Sustainable management of medical plastic waste through carbon dioxide-assisted pyrolysis

Sustainable production of aromatics via catalytic pyrolysis of polyolefins towards the carbon cycle for plastics

Co-pyrolysis-reforming of Biomass and Residues from Waste Polymer Pyrolysis for CO2 Reduction and Syngas Enhancement

Catalytic Pyrolysis of Polystyrene over Steel Slag under CO2 Environment

Valorization of Plastics and Paper Mill Sludge into Carbon Composite and Its Catalytic Performance for Acarbon Material Consisted of the Multi-Layerzo Dye Oxidation.

Co-Processing of Biomass and Plastics Waste Via Integrated Pyrolysis-Gasification Approach: Recent Advances, Challenges, and Opportunities

Co-processing plastics waste and biomass by pyrolysis–gasification: a review

Impact of CO 2 on the Pyrolysis of Mixed Polymer Wastes into Combustible Fuel: A Case Study for Footwear Waste

Enhanced biofuel production by co-pyrolysis of distiller's grains and waste plastics: A quantitative appraisal of kinetic behaviors and product characteristics

CO 2 enhanced continuous microwave pyrolysis of low-density polyethylene to produce high-quality products: Energy recovery balance and intrinsic mechanism exploration

CO2 facilitated upcycling of polyolefin plastics to aromatics at low temperature