Abstract:The thermal conversion of waste plastic products can provide a promising solution to the issues of environmental pollution, waste management, and energy needs. However, our present understanding on the thermal reforming of different kinds of plastic wastes mixtures during their co-pyrolysis and co-gasification for syngas production and energy recovery is insufficient. Non-selective urban polypropylene (PP) and polystyrene (PS) waste plastics were chosen for the investigations reported here. Thermal degradation properties of PP and PS as well as their blends in different mass ratios were investigated via thermogravimetric (TG) analysis. Co-pyrolysis and CO 2 -assisted co-gasification of PP-PS blends were then conducted using a fixed-bed reactor at a temperature of 1173 K. Experimental results from the blends were then compared with the weighted value calculated from their component feedstocks to quantify the degree of synergistic effect. TG results showed that the co-treatment of PP and PS enhanced the respective devolatilization process. The co-pyrolysis of PP and PS enhanced their thermal cracking, leading to synergistic increases in the yields of H 2 , light hydrocarbons (HC) and total syngas. In co-gasification, the reforming reaction involving CO 2 was synergistically enhanced, resulting in the increased yields of H 2 and HC. The gasification reactivity of carbon black improved during the co-processing of PP and PS due to the synergistic effect between the two different kinds of plastics. Higher synergistic effects were observed from the plastic mixtures having higher PS content that resulted in increased yield of syngas. Co-gasification of PP-PS blends having 40% PP content (2P3S) exhibited the maximum synergistic effect on H 2 , CO, and total syngas showing increased yields by 88.8%, 77.7%, and 74.2% respectively. The lowest synergistic effect was observed for HC that showed increased yield of only 25.1%. The optimal CO 2 consumption was also observed from the co-gasification of 2P3S. Each gram of 2P3S feedstock consumed approximately 1.80 g of CO 2 to result in highest recovered energy of 27.49 kJ/g and the maximum overall energy efficiency of 43.2%. The results revealed that enhanced thermal cracking and CO 2 reforming reaction, along with the improved reactivity of carbon black were mainly responsible for increased yields of H 2 , HC, CO and total syngas during co-gasification. This study contributes to the fundamental understanding of co-processing of non-separated waste plastics for enhanced syngas production and energy recovery, elucidating the synergistic effect between the various kinds of plastics during their co-pyrolysis and co-gasification.

Leveraging CO2 to directionally control the H2/CO ratio in continuous microwave pyrolysis/gasification of waste plastics: Quantitative analysis of CO2 and density functional theory calculations of regulation mechanism

CO 2 enhanced continuous microwave pyrolysis of low-density polyethylene to produce high-quality products: Energy recovery balance and intrinsic mechanism exploration

Analysis on low-temperature polyethylene pyrolysis and gasification in different atmospheres

Pyrolysis of Polyolefins Using Rotating Arc Plasma Technology for Production of Acetylene

Experimental study on CO 2 co-gasification characteristics of biomass and waste plastics: Insight into interaction and targeted regulation method

Controlling the compositional matrix of pyrogenic products using carbon dioxide in the pyrolysis of agricultural plastic waste

Microscopic mechanism for CO 2 -assisted co-gasification of polyethylene and softwood lignin: A reactive force field molecular dynamics study

Enhanced combined H2O/CO2 reforming of sludge to produce high-quality syngas via spiral continuous microwave pyrolysis technology: CO2 reforming mechanism and H2/CO directional regulation

Synergistic effects of CO2 on complete thermal degradation of plastic waste mixture through a catalytic pyrolysis platform: A case study of disposable diaper

Disposal of plastic mulching film through CO2-assisted catalytic pyrolysis as a strategic means for microplastic mitigation

Production of C5-C12 olefins by catalytic pyrolysis of low-density polyethylene with MCM-41 in CO2/N2

Syngas production through CO 2 -mediated pyrolysis of polyoxymethylene

Co-Processing of Biomass and Plastics Waste Via Integrated Pyrolysis-Gasification Approach: Recent Advances, Challenges, and Opportunities

CO2 Intensified Supercritical Water Gasification of Waste Plastics

Pyrolysis of Plastics-Free Refuse Derived Fuel Derived from Municipal Solid Waste and Combustion of the Char Products in Lab and Pilot Scales: A Comparative Study

Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene

Co-pyrolysis-reforming of Biomass and Residues from Waste Polymer Pyrolysis for CO2 Reduction and Syngas Enhancement

Microwave-assisted Chemical Looping Gasification of Plastics for H2-rich Gas Production

Research on co-gasification of polyethylene and cellulose via reactive molecular dynamics simulation

Improvement of Aromatics Selectivity from Catalytic Pyrolysis of Low-Density Polyethylene with Metal-Modified HZSM-5 in a CO2 Atmosphere

Exploration on the steam gasification mechanism of waste PE plastics based on ReaxFF-MD and DFT methods