Abstract:The thermal conversion of waste plastic products can provide a promising solution to the issues of environmental pollution, waste management, and energy needs. However, our present understanding on the thermal reforming of different kinds of plastic wastes mixtures during their co-pyrolysis and co-gasification for syngas production and energy recovery is insufficient. Non-selective urban polypropylene (PP) and polystyrene (PS) waste plastics were chosen for the investigations reported here. Thermal degradation properties of PP and PS as well as their blends in different mass ratios were investigated via thermogravimetric (TG) analysis. Co-pyrolysis and CO 2 -assisted co-gasification of PP-PS blends were then conducted using a fixed-bed reactor at a temperature of 1173 K. Experimental results from the blends were then compared with the weighted value calculated from their component feedstocks to quantify the degree of synergistic effect. TG results showed that the co-treatment of PP and PS enhanced the respective devolatilization process. The co-pyrolysis of PP and PS enhanced their thermal cracking, leading to synergistic increases in the yields of H 2 , light hydrocarbons (HC) and total syngas. In co-gasification, the reforming reaction involving CO 2 was synergistically enhanced, resulting in the increased yields of H 2 and HC. The gasification reactivity of carbon black improved during the co-processing of PP and PS due to the synergistic effect between the two different kinds of plastics. Higher synergistic effects were observed from the plastic mixtures having higher PS content that resulted in increased yield of syngas. Co-gasification of PP-PS blends having 40% PP content (2P3S) exhibited the maximum synergistic effect on H 2 , CO, and total syngas showing increased yields by 88.8%, 77.7%, and 74.2% respectively. The lowest synergistic effect was observed for HC that showed increased yield of only 25.1%. The optimal CO 2 consumption was also observed from the co-gasification of 2P3S. Each gram of 2P3S feedstock consumed approximately 1.80 g of CO 2 to result in highest recovered energy of 27.49 kJ/g and the maximum overall energy efficiency of 43.2%. The results revealed that enhanced thermal cracking and CO 2 reforming reaction, along with the improved reactivity of carbon black were mainly responsible for increased yields of H 2 , HC, CO and total syngas during co-gasification. This study contributes to the fundamental understanding of co-processing of non-separated waste plastics for enhanced syngas production and energy recovery, elucidating the synergistic effect between the various kinds of plastics during their co-pyrolysis and co-gasification.

Microscopic mechanism for CO 2 -assisted co-gasification of polyethylene and softwood lignin: A reactive force field molecular dynamics study

Research on co-gasification of polyethylene and cellulose via reactive molecular dynamics simulation

Revealing the mechanism on steam co-gasification of cellulose and polyethylene: A combined ReaxFF and DFT study

Analysis on low-temperature polyethylene pyrolysis and gasification in different atmospheres

Microscopic reaction mechanism for CO2 gasification of cellulose based on reactive force field molecular dynamics simulations

Experimental study on CO 2 co-gasification characteristics of biomass and waste plastics: Insight into interaction and targeted regulation method

Investigation on reaction mechanism for CO 2 gasification of softwood lignin by ReaxFF MD method

A study on co-pyrolysis mechanisms of biomass and polyethylene via ReaxFF molecular dynamic simulation and density functional theory

Co-gasification of biomass and polyethylene: a simulation study by considering tar formation

Leveraging CO2 to directionally control the H2/CO ratio in continuous microwave pyrolysis/gasification of waste plastics: Quantitative analysis of CO2 and density functional theory calculations of regulation mechanism

CO 2 utilization in chemical looping gasification and co-gasification of lignocellulosic biomass components over iron-based oxygen carriers: Thermogravimetric behavior, synergistic effect, and reduction characteristics

Synergistic interactions between cellulose and plastics (PET, HDPE, and PS) during CO2 gasification-catalytic reforming on Ni/CeO2 nanorod catalyst

Deciphering Interactions Between Biomass Components During CO2 Gasification: Insights from Thermogravimetric Behavior, Gas Production, and Char Reactivity

Catalytic co-gasification optimization of biomass and polyethylene wastes in oxygen-rich environments

Co-pyrolysis of biomass and polyethylene: Mechanistic insights into functional group transformations on solid matrix

CO 2 enhanced continuous microwave pyrolysis of low-density polyethylene to produce high-quality products: Energy recovery balance and intrinsic mechanism exploration

Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene

Synergistic interactions and co-pyrolysis characteristics of lignocellulosic biomass components and plastic using a fast heating concentrating photothermal TGA system

Structure characteristics and gasification reactivity of co-pyrolysis char from lignocellulosic biomass and waste plastics: Effect of polyethylene

Synergetic effects in the co-pyrolysis of lignocellulosic biomass and plastic waste for renewable fuels and chemicals

Thermogravimetric Analysis on Co-Gasification Characteristics of Sludge and Straw under CO2 Atmosphere