Abstract:The research investigates the metallurgical and mechanical properties of multi-layered built-up of SS316L produced through cold metal transfer-based wire arc additive manufacturing. The present study focused on varying heat input and its effect on the structural properties of built-ups. The WAAMed deposits showcase the fusion lines resembling an arc-like shape without porosity or inter-layer interfaces, and that signifies the sound and defect-free built-up fabrication. The WAAMed walls have shown a dual-phase microstructure comprising γ-austenite and δ-ferrite along with associated solidification modes. The distribution of these phases is affected by heat input variations, leading to a decline in γ-austenite concentration and a rise in δ-ferrite and micro-inclusions with higher heat inputs. Concurrently, grain size and secondary dendrite arm spacing (SDAS) escalate proportionally with increased heat input, with grain size ranging from 8.23 to 11.16 μm and SDAS from 5.68 to 8.27 μm across different heat inputs. Oxygen-based micro-inclusions also increased with an increase in heat input. Vickers microhardness assessments illustrate a decline in hardness as heat input rises. The low heat input wall exhibits an average hardness of 191.056 HV, while the high heat wall exhibits an average hardness of 171.90 HV. A 10.56% drop in hardness for a 52.88% increase in heat input is observed. Impact energy also decreased as heat input increased. For low, medium, and high heat inputs, the average impact energy from bottom to top portions of walls was 115, 97.22, and 84 J, respectively. 1.528-fold increase in heat input leading to a 1.369-fold decrease in impact energy. Reducing heat input led to significant improvements in yield strength (408.66 ± 2.21 to 361 ± 1.67 MPa) and ultimate tensile strength (630.33 ± 3.75 to 577.33 ± 1.43 MPa), corresponding to increases of approximately 12.20% and 7.56%, respectively. Conversely, percent elongation decreased from 54.26 ± 1.2 to 42.83 ± 3.9%, marking a reduction of 22.22%. Fractured specimens exhibit uniformly dispersed dimples and micro-voids, signifying ductile fracture behavior indicative of good toughness. The obtained results indicate that the lower heat input would be preferential for WAAMed built-up in the context of mechanical and microstructural properties compared to high heat input for the built-up fabrication.

Effect of heat input on microstructural and mechanical properties of high strength low alloy steel block parts fabricated by wire arc additive manufacturing

Improving mechanical strength and isotropy for wire-arc additive manufactured 304L stainless steels via controlling arc heat input

Mechanical Properties, Microstructural Characteristics and Heat Treatment Effects of WAAM Stainless-Steel Plate Material

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Improve the Manufacturing Efficiency of Steel Bars by Using Hot-Wire Pulse Arc Additive Manufacturing

Study on Heat Input Effect of 316L Stainless Steel Thin-Walled Parts Processed by Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of 800-MPa-Class High-Strength Low-Alloy Steel Part Fabricated by Wire Arc Additive Manufacturing

Effect of Heat Inputs on the Microstructures and Properties of 316L Stainless Steel Parts Manufactured by Wire and Arc Additive Manufacturing Processing

Wire Arc Additive Manufacturing of ZL205A: Heat Input Effect on the Forming Quality、pore Defects and Mechanical Properties

Effect of welding parameters on microstructure and mechanical properties of mild steel components produced by WAAM

Experimental study on the heat input behavior of wire-arc additively manufactured 316L stainless steel parts for repairing applications

Comparison of microstructural characteristics and mechanical properties of the high-strength low-alloy steels fabricated by wire arc additive manufacturing versus conventional casting

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

A Comparative Study of Microstructural Characteristics and Mechanical Properties of High-Strength Low-Alloy Steel Fabricated by Wire-Fed Laser Versus Wire Arc Additive Manufacturing

Effect of equivalent heat input on WAAM Al-Si alloy

Effect of thermal history on microstructure evolution and mechanical properties in wire arc additive manufacturing of HSLA steel functionally graded components

Microstructure and Mechanical Properties of Low-Carbon High-Strength Steel Fabricated by Wire and Arc Additive Manufacturing

On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

Heat control and design-related effects on the properties and welding stresses in WAAM components of high-strength structural steels

Effect of Interlayer Temperature on Microstructure and Properties of High-Strength Low-Alloy Steel Manufactured Using Submerged-Arc Additive Manufacturing (SAAM)

Performance Evaluation of Cold Metal Transfer-Based Wire Arc Additive Manufacturing of SS316L: An Effect of Weld Thermal Cycles and Heat Inputs