Abstract:This study aims to enhance the rheological behavior of SiC/Clay paste with the use of 3 types of polymers (CMC, PEG, and PVA) to obtain better printability through the Direct ink writing method pastes prepared by stirring polymer solutions with SiC/Clay powders. Rheometry and zeta potential tests are used to characterize pastes properties. 20 x 20 mm scaffolds were 3D printed then dried for 24h at room temperature and sintered at 1300°C for 1h to obtain the mullite phase in the final product. In this study, we investigated the impact of polyethylene glycol, sodium carboxymethyl cellulose, and polyvinyl alcohol on the rheological behavior, printability, and mechanical/physical properties of 3D‐printed scaffolds for high‐temperature applications using SiC/clay ceramic paste. Employing the Direct Ink Writing method, varying concentrations of each polymer (PEG: 2.5%–10% weight, CMC: .6%–1.8% weight, PVA: .25%–1% weight) were incorporated into the composition. The resulting SiC/clay paste, with adjusted additive content, was used to 3D‐print scaffold structures through Direct Ink Writing. Sintering of clay‐bonded SiC samples were carried out at 1300°C for 1 h in an ambient atmosphere. The research revealed that altering the additive amounts significantly influenced the rheological behavior, mechanical properties, and physical characteristics of the printed specimens. Notably, the ideal properties with additive concentrations (10% wt PEG, 1% wt PVA, and .6% CMC) were identified, providing the best outcomes in terms of printability and firing results. High density samples with 2.09, 1.93, and 1.79 g/cm3, high compression strength of 20.82, 14.5 and 12.53 MPa with 32.26%, 42.5%, and 52.63% open porosity for samples containing PVA, CMC, and PEG modifiers were obtained, respectively. Additionally, the study led to the development of a high solid loading printable paste with an 80% weight.

A comparative evaluation of sepiolite and nano-montmorillonite on the rheology of cementitious materials for 3D printing

Properties and Microstructures of 3D Printable Sulphoaluminate Cement Concrete Containing Industrial By-Products and Nano Clay

The Role of Different Clay Types in Achieving Low-Carbon 3D Printed Concretes

Enhancing the performance of 3D-printed fiber-Reinforced mortar: synergistic effects of clays and bacterial cells as viscosity modifying agents

An investigation of rheological properties and sustainability of various 3D printing concrete mixtures with alternative binders and rheological modifiers

Effect of Nanostructured Silica Additives on the Extrusion-Based 3D Concrete Printing Application

Assessment of materials, design parameters and some properties of 3D printing concrete mixtures; a state-of-the-art review

Effect of supplementary cementitious materials on properties of 3D printed conventional and alkali-activated concrete: A review

Effect of different grade levels of calcined clays on fresh and hardened properties of ternary-blended cementitious materials for 3D printing

Investigating the effect of polymer additives on the rheology of SiC/clay paste for use in Direct Ink Writing method

Effects of cellulose nanofibrils on rheological and mechanical properties of 3D printable cement composites

Effects of bentonite, diatomite and metakaolin on the rheological behavior of 3D printed magnesium potassium phosphate cement composites

Comparison of the Effect of Nano Cellulosic Additives on Rheological Parameters for 3D Printable Concretes

3D Printing of Fiber-Reinforced Calcined Clay-Limestone-Based Cementitious Materials: From Mixture Design to Printability Evaluation

Review of Advances in 3D Printing Technology of Cementitious Materials: Key Printing Parameters and Properties Characterization

Effect of Silica Fume Utilization on Structural Build-Up, Mechanical and Dimensional Stability Performance of Fiber-Reinforced 3D Printable Concrete

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Effect of TiO2 Nanoparticles on the Fresh Performance of 3D-Printed Cementitious Materials

Effect of nano clay and PCE on the buildability of ultra-fine dredged sand-based 3D printing materials

Improving printability of limestone-calcined clay-based cementitious materials by using viscosity-modifying admixture