Abstract:The study focuses on the development of cementitious composites using 3D printing and plastic waste as a sustainable aggregate substitute. This study involves experimenting with various percentages of plastic waste as a partial substitute for ground granulated blast furnace slag (GGBFS) in a control mix. The study examines the anisotropy of the 3D printing process, comparing it with properties of mold-cast samples. In addition, it assesses the fire resistance and mechanical properties of samples at elevated temperatures (100 °C, 300 °C, and 600 °C). Key mechanical properties, including 28-day compressive stress and flexural strength, are determined through experimental testing using a standard compression test and three-point bending test. The study also considers the modulus of elasticity (MOE) in compressive tests to evaluate a sample's ability to deform elastically and the flexural toughness index to assess energy absorption and crack resistance of flexural samples. Following the experimental testing, the study's key findings suggest that significant mass loss occurred at 300 °C and above, with plastic samples demonstrating increased mass loss at 600 °C. At 600 °C, plastic degradation led to the formation of voids and cracks within samples due to heightened internal pressure. Anisotropy was evident in 3D-printed samples, with loads parallel to the layer direction resulting in greater compressive strength and MOE. Furthermore, layer direction parallel to the longitudinal axis of flexural samples yielded higher flexural strength and flexural toughness. Mold-cast samples displayed superior compressive strength and stiffer behavior, with higher MOE compared to 3D-printed samples. However, 3D-printed plastic samples exhibited superior flexural strength compared to mold-cast samples, attributed to the alignment of plastic within the samples. The study also observed a reduction in compressive strength with the addition of plastic, explained by the poor bonding of plastic with cement due to its hydrophobic nature. Despite this, flexural strength generally improved with plastic addition, except at 600 °C, where plastic samples showed significant degradation in both compressive and flexural strength due to plastic degradation within the samples.

An investigation of rheological properties and sustainability of various 3D printing concrete mixtures with alternative binders and rheological modifiers

Properties and Microstructures of 3D Printable Sulphoaluminate Cement Concrete Containing Industrial By-Products and Nano Clay

Sustainable materials for 3D concrete printing

Effect of Silica Fume Utilization on Structural Build-Up, Mechanical and Dimensional Stability Performance of Fiber-Reinforced 3D Printable Concrete

3D Printing of Fiber-Reinforced Calcined Clay-Limestone-Based Cementitious Materials: From Mixture Design to Printability Evaluation

Investigation of the rheological and mechanical properties of 3D printed eco-friendly concrete with steel slag

3D printing eco-friendly concrete containing under-utilised and waste solids as aggregates

Effect of supplementary cementitious materials on properties of 3D printed conventional and alkali-activated concrete: A review

Improving printability of limestone-calcined clay-based cementitious materials by using viscosity-modifying admixture

A rheological-based printability assessment method for 3D printing Engineered Cementitious Composites considering fiber dispersion

Eco-friendly 3D printed concrete with fine aggregate replacements: Fabrication, characterization and machine learning prediction

Enhancing the performance of 3D-printed fiber-Reinforced mortar: synergistic effects of clays and bacterial cells as viscosity modifying agents

Development of concrete mixes for 3D printing using simple tools and techniques

A comparative evaluation of sepiolite and nano-montmorillonite on the rheology of cementitious materials for 3D printing

Mechanical Properties and Fire Resistance of 3D-Printed Cementitious Composites with Plastic Waste

Comparative Evaluation of the Applicability of 3D Printing Mortar with Different Waste Powders

Systematic approach for printability evaluation and mechanical property optimization of spray-based 3D printed mortar

Rheological characterization of ultra-high performance concrete for 3D printing

Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances

Tailoring Light-Weight Aggregates for Concrete 3D Printing Applications

Towards Sustainable Material: Optimizing Geopolymer Mortar Formulations for 3D Printing: A Life Cycle Assessment Approach