Abstract:Compression plates are widely used in orthopaedic surgeries for internal fixation of fractured femurs. To fix the plate and thus to provide compression to a fracture, the self-tapping bone screws are tightened through predrilled pilot holes of smaller diameter. Preliminary investigation showed that the holes drilled with the inappropriate cutting parameters cause mechanical and thermal damages to the local host bone, which further lead to loosening of internal fixations. In this paper, the mechanistic models to predict the thrust forces and torques during bone drilling were developed, using a 3.20 mm diameter drill bit. As a procedure, the cutting action was investigated at three different regions of the drill point, namely cutting lips, secondary cutting edges and indentation zone. The models employed the analytical approach to account for the drill-bit geometry and cutting parameters, and an empirical approach to account for the material and friction properties. To complete the procedure, calibration experiments were conducted on bovine cortical femurs with two different spindle speeds (1000 and 3000 r/min) and feeds (0.03 and 0.06 mm/rev), and then the specific normal and friction coefficients were determined. The developed mechanistic models were validated with different ranges of parameters (500–3500 r/min speeds, and 0.02–0.07 mm/rev feeds) those commonly involved in manual and robot-assisted surgery. The validation study revealed that the thrust forces predicted using the mechanistic models showed a maximum error of only 5.80%. However, the torques predicted from the mechanistic model found with more error than the thrust forces. The predominant reasons for this under-prediction might because of the extrapolation used to determine the specific cutting pressures, slip-line field applied to the indentation zone instead of compressive fracture, and chip clogging involved during the bone drilling as demonstrated in earlier studies. Despite the deviations, the developed mechanistic models satisfactorily follow the trends of the thrust forces and torques experienced during bone drilling. The outcomes can be used to practice the bone drilling procedure and monitor the effect of process parameters on thrust forces and torques in the in-silico environment before performing actual surgery.

Prediction of surface roughness and cutting force induced during rotary ultrasonic bone drilling via statistical and machine learning algorithms

Deep learning-based temperature prediction during rotary ultrasonic bone drilling

Prediction of surface roughness and depth of cut in abrasive waterjet milling of alumina ceramic using Machine learning algorithms

Mechanistic models to predict thrust force and torque in bone drilling: An in-vitro study validated with robot-assisted surgical drilling parameters

A Mathematical Model for Predicting Cutting Force in Rotary Ultrasonic Drilling

Next-Gen Manufacturing: Machine Learning for Surface Roughness Prediction in Ti-6Al-4V Biocompatible Alloy Machining

Material Removal Mechanism and Force Modeling in Ultrasonic Vibration-Assisted Micro-Grinding Biological Bone

Implementing Machine Learning approaches for accelerated prediction of bone strain in acetabulum of a hip joint

Prediction of Surface Roughness Using Machine Learning Approach in MQL Turning of AISI 304 Steel by Varying Nanoparticle Size in the Cutting Fluid

Surface Feature Prediction for Laser Ablated 40Cr13 Stainless Steel Based on Extreme Learning Machine

Prediction of cutting force via machine learning: state of the art, challenges and potentials

Development of empirical models for the prediction of surface functional parameters in ultrasonic elliptical vibration cutting

Machine learning approach for prediction analysis of aluminium alloy on the surface roughness using CO2 laser machining

Prediction of Cutting Forces in Milling Using Machine Learning Algorithms and Finite Element Analysis

Correlation between intraosseous thermal change and drilling impulse data during osteotomy within autonomous dental implant robotic system: An in vitro study

Multiobjective Optimization of Surface Roughness and Tool Wear in High-Speed Milling of AA6061 by Machine Learning and NSGA-II

Force Perception and Bone Recognition of Vertebral Lamina Milling by Robot-Assisted Ultrasonic Bone Scalpel Based on Backpropagation Neural Network

Integrating machine learning for predicting biomechanical properties of layered manufactured bone implants

Influence of cutting force on temperature, microcracks and chip morphology during rotary ultrasonic bone drilling: An in-vitro study

Using artificial intelligence to predict surface roughness in deep drilling of steel components

Machine learning approach for predicting the machining characteristics of additive manufactured ABS material