Abstract:Silica-based ceramic cores are widely used in the manufacturing of hollow, nickel-based, superalloy turbine blades. However, elemental Hf, Ti, Al, and other active metals in the superalloy can react with silica-based ceramic cores during casting, resulting in a reduction in the quality of the turbine blades. In this study, both plasma spraying and sol-gel dipping methods were used to prepare alumina coatings on silica-based ceramic substrates to prevent the interfacial reaction. The performance of the alumina coatings prepared by both methods was evaluated by comparative analysis of the surface roughness, bonding interface morphologies, and the adhesive characteristics of the coating. The plasma-sprayed alumina coating has a roughness greater than 5 μm and peeled away from the substrate due to the difference in thermal expansion between SiO2 and Al2O3 at temperatures above 1500 °C, rendering the silica-based substrate with the plasma-sprayed alumina coating unfit for the application requirements of the casting process. The alumina coating prepared by the sol-gel dipping method improved the roughness of the substrate from Ra 2.39 μm to Ra 1.83 μm, and no peeling was observed when heated to 1550 °C for 30 min due to the pinning characteristics of the coating on the substrate. Furthermore, the interfacial reaction between the DZ125 superalloy melt and the silica-based substrate coated with alumina by sol-gel dipping method were investigated. The alumina coating effectively inhibited the interfacial reaction and no reaction products were detected during the directional solidification with pouring temperature of 1550 °C and withdraw rate of 5 mm/min. While a uniform, 4–5 μm thick HfO2 reaction layer formed between the uncoated substrate and the DZ125 alloy melt. Two dipping-drying cycles were required to ensure the alumina sol completely covered the surface of the substrate.

Development of mullite-alumina ceramic shells for precision investment casting of single-crystal high-pressure turbine blades

Alumina-based ceramic mold with integral core and shell for hollow turbine blades fabricated by Laser powder bed fusion

Microstructure Evolution and Mechanical Behaviors of Alumina-Based Ceramic Shell for Directional Solidification of Turbine Blades

Microstructure Evolution and Mechanical Properties of Ceramic Shell Moulds for Investment Casting of Turbine Blades by Selective Laser Sintering

Single crystal casting of gas turbine blades using superior ceramic core

Additive manufacturing of low-shrinkage alumina cores for single-crystal nickel-based superalloy turbine blade casting

Experimental study on high temperature performances of silica-based ceramic core for single crystal turbine blades

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Microstructure and Crystallization Kinetics of Silica-Based Ceramic Cores with Enhanced High-Temperature Property

Effect of Sintering Temperature on Microstructure and Mechanical Behavior of Alumina-Based Ceramic Shell by SLS

Properties of alumina coatings prepared on silica-based ceramic substrate by plasma spraying and sol-gel dipping methods

Reinforcement of silica-based ceramic cores based on amorphous and polycrystalline mullite fibers

Synthesis, protection performance, and failure analysis of α-Al2O3/Mo(Si,Al)2 coatings

Evaluating Silicon Carbide-Based Slurries and Molds for the Manufacture of Aircraft Turbine Components by the Investment Casting

Effect of sodium silicate solution combined yttrium oxide stabilized zirconia nanopowders on the properties of alumina ceramics fabricated by binder jetting additive manufacturing

Probing the failure mechanisms and microstructure evolution of a high-pressure turbine blade coated with AlSiY

An investigation of ceramic shell thickness uniformity and its impact on precision in turbine blade investment casting

Dynamic Response of Ceramic Shell for Titanium Investment Casting under High Strain-Rate SHPB Compression Load

Investigation of Fused Alumina Based-Mold Facecoats for DZ22B Directionally Solidified Blades

Processing and Characterization of AA2618/Sicp Metal Matrix Composites by Stir Casting Method

Effect of casting thickness on microstructure and mechanical properties of the high-W superalloy K416B