Abstract:Modulation of the microstructure and configurational entropy tuning are the core stratagem for improving thermoelectric performance. However, the correlation of evolution among the preparation methods, chemical composition, structural defects, configurational entropy, and thermoelectric properties is still unclear. Herein, two series of AgSbTe2-based compounds were synthesized by an equilibrium melting-slow-cooling method and a nonequilibrium melting-quenching-spark plasma sintering (SPS) method, respectively. The equilibrium method results in coarse grains with a size of >300 μm in the samples and a lower defect concentration, leading to higher carrier mobility of 10.66 cm2 V-1 s-1 for (Ag2Te)0.41(Sb2Te3)0.59 compared to the sample synthesized by nonequilibrium preparation of 1.83 cm2 V-1 s-1. Moreover, tuning the chemical composition of nonstoichiometric AgSbTe2 effectively improves the configurational entropy and creates a large number of cation vacancies, which evolve into dense dislocations in the samples. Owing to all of these in conjunction with the strong inharmonic vibration of lattice, an ultralow thermal conductivity of 0.51 W m-1 K-1 at room temperature is achieved for the (Ag2Te)0.42(Sb2Te3)0.58 sample synthesized by the equilibrium preparation method. Due to the enhanced carrier mobility, optimized carrier concentration, and low thermal conductivity, the (Ag2Te)0.42(Sb2Te3)0.58 sample synthesized by the equilibrium preparation method possesses the highest ZT of 1.04 at 500 K, more than 60% higher than 0.64 at 500 K of the same composition synthesized by nonequilibrium preparation.

An effective synthesis route for high-performance α-MgAgSb thermoelectric material

Cost Effective Synthesis of P-Type Zn-doped MgAgSb by Planetary Ball-Milling with Enhanced Thermoelectric Properties

Intrinsically high thermoelectric performance in near-room-temperature α-MgAgSb materials

A Route to High Thermoelectric Performance: Solution‐Based Control of Microstructure and Composition in Ag2Se

High thermoelectric performance of MgAgSb-based materials

Optimization of the thermoelectric performance of α-MgAgSb-based materials by Zn-doping

High Performance Α-Mgagsb Thermoelectric Materials for Low Temperature Power Generation

Enhanced Thermoelectric Performance of Mg-Doped AgSbTe 2 by Inhibiting the Formation of Ag 2 Te

Simple Synthesis and Thermoelectric Properties of Mg2 + xSi0.5Sn0.5Sb0.075 Materials with Heterogeneous Microstructure

Enhancing the Thermoelectric Performance of Mgagsb-Based Materials with Heavy Zn-Doped

Enhancing Thermoelectric Performance of AgSbTe 2 -Based Compounds via Microstructure Modulation Combining with Entropy Engineering

Thermoelectric performance enhancement of Pb-doped α -MgAgSb near room temperature

Bismuth-free Mg3Sb2 with Enhanced Room-Temperature Thermoelectric and Mechanical Properties

Enhancing Thermoelectric Performance of AB2Sb2-type Zintl Phase Through Band Shaping and Lattice Distortion

Synthesis of Nanocomposites with Improved Thermoelectric Properties

High-performance Ag0.8Pb18+xSbTe20 Thermoelectric Bulk Materials Fabricated by Mechanical Alloying and Spark Plasma Sintering

Energy-Efficient Synthesis and Superior Thermoelectric Performance of Sb-doped Mg2Si0.3Sn0.7 Solid Solutions by Rapid Thermal Explosion

Ultra-Fast Synthesis for Ag2Se and CuAgSe Thermoelectric Materials

Suppressing Ag2Te Nanoprecipitates for Enhancing Thermoelectric Efficiency of AgSbTe2

High Thermoelectric Conversion Efficiency of MgAgSb-based Material with Hot-Pressed Contacts

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect