Abstract:Abstract Microstructure control in the laser powder bed fusion additive manufacturing processes is a topic of major interest because of the submillimeter length scale at which the manufacturing process occurs. The ability to control the process at the melt pool scale allows for microstructure control that few other manufacturing techniques can match. The majority of work on microstructure control has focused on altering laser parameters to control solidification conditions (Ref (R.R. Dehoff, M.M. Kirka, W.J. Sames, H. Bilheux, A.S. Tremsin, L.E. Lowe, and S.S. Babu, Site Specific Control of Crystallographic Grain Orientation through Electron Beam Additive Manufacturing, Mater. Sci. Technol., 2014, 31 (8), p 931–938. R. Shi, S.A. Khairallah, T.T. Roehling, T.W. Heo, J.T. McKeown, and M.J. Matthews, Microstructural Control in Metal Laser Powder Bed Fusion Additive Manufacturing Using Laser Beam Shaping Strategy, Acta Mater., 2020, 184 , p 284–305, https://doi.org/10.1016/j.actamat.2019.11.053 .)). Other machine parameters, besides the laser parameters, have also been shown to affect the microstructure of AM parts (Ref (N. Nadammal, S. Cabeza, T. Mishurova, T. Thiede, A. Kromm, C. Seyfert, L. Farahbod, C. Haberland, J.A. Schneider, P.D. Portella, and G. Bruno, Effect of Hatch Length on the Development of Microstructure, Texture and Residual Stresses in Selective Laser Melted Superalloy Inconel 718, Mater. Des., 2017, 134 , p 139–150, https://doi.org/10.1016/j.matdes.2017.08.049 . F. Geiger, K. Kunze, and T. Etter, Tailoring the Texture of IN738LC Processed by Selective Laser Melting (SLM) by Specific Scanning Strategies, Mater. Sci. Eng. A, 2016, 661 , p 240–246, https://doi.org/10.1016/j.msea.2016.03.036 .)). We propose an investigation of the effects of hatch spacing and layer thickness on microstructure development in laser powder bed fusion additive manufacturing. A Monte Carlo Potts model with textured solidification capabilities is used to study the effects of these parameters on a unidirectional scan strategy. The simulation results reveal substantial changes in grain morphology as well as texture. Additionally, EVP-FFT crystal plasticity simulations were performed to evaluate the effect of the microstructural shifts on mechanical response. The conclusions from this work elucidate the effects of these parameters on part microstructure as predicted by the texture-aware solidification Potts model and inform understanding of how bulk texture is predicted by the simulation approach.

The effect of hatch angle rotation on parts manufactured using selective laser melting

The Effect of Scanning Strategy on the Thermal Behavior and Residual Stress Distribution of Damping Alloys during Selective Laser Melting

Geometrical effects on residual stress in selective laser melting

The effect of selective laser melting process parameters and remelting scanning strategy on relative density and surface hardness of stainless steel 316L

Simulation Study of Hatch Spacing and Layer Thickness Effects on Microstructure in Laser Powder Bed Fusion Additive Manufacturing using a Texture-Aware Solidification Potts Model

Coupling Analysis on Microstructure and Residual Stress in Selective Laser Melting (SLM) with Varying Key Process Parameters

Selective laser melting (SLM) of AISI 316L—impact of laser power, layer thickness, and hatch spacing on roughness, density, and microhardness at constant input energy density

Surface Roughness Control of Root Analogue Dental Implants Fabricated Using Selective Laser Melting

Rotating Scan Strategy Induced Anisotropic Microstructural and Mechanical Behavior of Selective Laser Melted Materials and Their Reduction by Heat Treatments

Effect of Process Parameters on Residual Stresses, Distortions, and Porosity in Selective Laser Melting of Maraging Steel 300

Study of residual stress in selective laser melting of Ti6Al4V

The effect of hatch distance on the microstructure and mechanical properties of Ti15Mo prepared by selective laser melting

Scanning strategy in selective laser melting (SLM): a review

Effect of hatch distance on CuSn10 specimens by selective laser melting

Influences of Tilt Angles on Microstructure and Mechanical Properties of 316L Stainless Steel Parts Fabricated by Selective Laser Melting (SLM)

The Effect of a Scanning Strategy on the Residual Stress of 316L Steel Parts Fabricated by Selective Laser Melting (SLM)

Residual Stress Distribution in Selective Laser Melting of SS316L Parts

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V

Investigation into the effect of process parameters on microstructural and physical properties of 316L stainless steel parts by selective laser melting

An experimental investigation of the influence of SLM input factors on the as-built AlSi10Mg surface quality

Influence of Typical Technological Parameters on the Forming Quality of TA1 in Selective Laser Melting