Abstract:Statement of problem: The selective laser melting (SLM) process has become popular for the fabrication of frameworks for metal-ceramic restorations, although their surface roughness is greater than with cast or milled frameworks. Limited information is available regarding the surface mechanical characteristics of cobalt-chromium (Co-Cr) SLM-manufactured restorations. Purpose: The purpose of this in vitro study was to adapt the laser parameters for a remelting strategy, scanning the outer boundary of Co-Cr specimens, to reduce surface roughness and solidification defects, to determine microhardness, to investigate surface morphology and microstructure, and to establish surface mechanical characteristics. Material and methods: Co-Cr specimens were SLM manufactured by using a typical melting (TM) strategy and an adaptive remelting (AR) strategy. The AR strategy involves rescanning 50% of the contour, varying the laser parameters. The roughness parameters considered were Ra and Rz. Vickers hardness was measured by microindentation with a 9.81-N force (ASTM E384-17). The surface morphology was investigated by scanning electron microscopy, the chemical composition by energy-dispersive X-ray spectroscopy, and the phase identification by using X-ray diffraction. The mechanical surface properties measured were the nanohardness, elastic modulus, and dissipation energy. One-way ANOVA with the Tukey procedure was used to compare the groups (α=.05). Results: The innovative AR strategy reduced the surface roughness by 45% compared with TM, comparable with their cast counterpart. The smoothest AR surface was obtained by using 75 W and 350 mm/s for the first scanning of the contour, followed by a second remelting with 80 W and 700 mm/s. The microstructure of AR specimens had limited solidification defects, a chemical composition similar to that of raw powder, and a surface microhardness over 600 HV1. A fine grain structure in a single matrix phase was detected both on TM and AR specimens. The mechanical characteristics of the smoothest Co-Cr surface were 218 GPa elastic modulus, 746 HVIT Vickers nanohardness, 21 243 pJ plastic energy, and 26% nanoindentation work ratio. Significant differences were observed between the melting strategies (P<.05) both for surface roughness and microhardness. Conclusions: The laser scanning strategy affects both the surface roughness and the hardness of SLM-manufactured specimens. The results show that using the AR strategy and proper laser parameters can reduce the roughness and increase the surface hardness of Co-Cr specimens made of conventional powder feedstock.

Surface Roughness Control of Root Analogue Dental Implants Fabricated Using Selective Laser Melting

Osteogenic Comparison On Selective Laser Melting Printed And Sandblasting-Acid-Etching Ti Substrates For Customized Implant Applications

Enhanced Osseointegration by the Hierarchical Micro-Nano Topography on Selective Laser Melting Ti-6Al-4V Dental Implants

Quality assurance thermophysical aspects of highly porous implants with cellular structure obtained by selective laser melting

Additive Manufacturing of Dental Root-Analogue Implant with Desired Properties

Evaluation of Root-Analog Implants and Standardized Specimens Fabricated by Selective Laser Melting

How does the surface treatment change the cytocompatibility of implants made by selective laser melting?

Fabrication and characterization of selective laser melting printed Ti–6Al–4V alloys subjected to heat treatment for customized implants design

Surface modification of porous titanium and titanium alloy implants manufactured by selective laser melting: A Review

Top surface roughness evolution during selective laser melting of AlCu5MnCdVA aluminum alloy

Impact of laser parameters on additively manufactured cobalt-chromium restorations

Micro-/nano-topography of selective laser melting titanium enhances adhesion and proliferation and regulates adhesion-related gene expressions of human gingival fibroblasts and human gingival epithelial cells

Surface modification improving the biological activity and osteogenic ability of 3D printing porous dental implants

Improving the Surface Roughness of Dental Implant Fixture by Considering the Size, Angle and Spraying Pressure of Sandblast Particles

Influence of Dental Implant Surface Modifications on Osseointegration and Biofilm Attachment

Improving the Mechanical Strength of Dental Applications and Lattice Structures SLM Processed

[Influence of Implants Prepared by Selective Laser Melting on Early Bone Healing].

Application of optimized laser surface re-melting process on selective laser melted 316L stainless steel inclined parts

Bio‐Inspired Micro‐ and Nano‐Scale Surface Features Produced by Femtosecond Laser‐Texturing Enhance TiZr‐Implant Osseointegration

Effect of laser process parameters on the pores, surface roughness, and hardness of laser selective melting of dental cobalt-chrome alloys

Porous structure design and properties of dental implants