Abstract:BackgroundThe paper represents the first comprehensive experimental and numerical study for engineering failure analysis and appropriate design for the permanent mechanical support system for the tomb of the Sons of Ramesses II (KV5). It is, in fact, one of the largest rock cut tombs ever found in Egypt. During the late 18th Dynasty and throughout the19th, the tombs are usually located further down the Valley some distance from the rock walls. The builders often quarried through talus slopes, such as in the case of the tomb of Sons of Ramses II. It is clear that the tomb of sons of Ramsses II is much more susceptible to surcharge geostatic loading from the overburden rock strata, rock bursting, and structural damage of support pillars and walls induced to the water and past/recent flash floods impacts caused by heavy rain in the Valley. Since some of this tomb also makes contact with the underlying shale layers, that have the potential for swelling and shrinkage under changing moisture conditions. Expansive damages to these underground structures have been widely noticed in the Valley of the Kings. This tomb tends to be the worst preserved tomb in the Valley of the Kings. The Esna shale in the valley is particularly weak and unstable. It not only posed problems to the ancient quarryman, but to the modern conservator as well. When the shale comes into contact with moisture, it expands and can literally tear a hill side apart.ResultsThe main adjectives of the geoenvironmental and geotechnical analyses carried out in the present study are to investigate the static stability, safety margins and engineering failure of the tomb of Sons of Ramsses II (KV5) under their present conditions, against unfavorable environmental (i.e. extensive weathering due to water and flash floods impact in the past and present), utter lack of preservation, geostatic overloading of structural rock support pillars, geotechnical and extreme seismic conditions. Also to design an appropriate geotechnical support system, according to the engineering rock mass classification, in particularly the rock mass rating RMR and quality rock tunneling index Q-system.ConclusionsThe engineering analysis had been carried out through the following four steps: 1-Evaluation of the surrounding rocks (marl limestone) by experimental investigation and the Roclab program to obtain Hoek Brown Classification criterion, Mohr- Coulomb fit and the rock mass parameters in particular the global strength and deformation modulus. 2- Qualitative and quantitative estimations of relevant factors affecting the stability of the tomb in particularly the overburden or geostatic and dynamic loading. 3- 2D and 3D integrated geotechnical modeling of the tomb environment for stress, displacement analyses and determination of volumetric strains and plastic points using advanced codes and programs like Examine 2D and PLAXIS 3D. The numerical analysis results indicated that the safety factor of the rock pillar structural supports is 1.37 and the overstress state is 1.28 MPa. 4-Remedial and retrofitting policies and techniques, static monitoring and control systems which are necessary for the strengthening and stability enhancement of the tomb, where the rock mass classification indicated the rock mass where the KV5 is excavated is poor rock, with RMR 39 and Q value 1.87.Based on the underground engineering stable equilibrium theory and rock mass classification, three support structure techniques are provided and detailed illustrated with the case of KV5 in this study.

Virtual testing of a new conjecture for the stone ascending device in Egyptian pyramids by means of a multibody dynamics simulation

A variational event-driven approach for the dynamic analysis of multi-block historical masonry structures under ground excitation

Fast Vulnerability Evaluation of Masonry Towers by Means of an Interactive and Adaptive 3D Kinematic Limit Analysis with Pre-assigned Failure Mechanisms

The Virtual Goniometer: A new method for measuring angles on 3D models of fragmentary bone and lithics

Seismic analysis of Islamic Egyptian minarets through 3D scanning and dynamic simulation

Experimental and Numerical Study on the Influence of Gravitational Stress Gradient on the Mechanical Behavior of 3D Printing Sandstone Models

On the possible use of hydraulic force to assist with building the step pyramid of saqqara

Modeling Shake-Table Tests of a Masonry Cross Vault Through the MADY Code

Simulative validation of a novel experiment carrier for the Einstein-Elevator

High-Resolution 3D FEM Stability Analysis of the Sabereebi Cave Monastery, Georgia

Using physics-based simulation towards eliminating empiricism in extraterrestrial terramechanics applications

State of the art of DSRW test equipment subjected to side loads and equipment proposal for static testing at natural scale

Combined Finite-Discrete Element Model Simulations of Shake-Table Tests on a Full-Scale Masonry Cross Vault

A New Analytical Solution for Calculating Rock Block Volume

Engineering failure analysis and design of support system for ancient Egyptian monuments in Valley of the Kings, Luxor, Egypt

Pre- and post-simulations of shake-table tests on a stone masonry building aggregate using finite-discrete elements

Large scale analogue experiments in rock mechanics : new experimental facility, 3D-printed material and insertion of force transducers for stresses measurement.

Design and simulation of a desk-size parallel kinematic machine for simulation of seismic events

Seismic numerical analysis of an Inca stone wall in Sacsayhuaman using rigid body dynamics within a finite element framework

Particle flow numerical study of size effect on uniaxial compressive strength of natural building stone

Simple model for predicting the vibration transmission of a squat masonry tower by base forced vibrations