Abstract:Bed joint reinforced repointing is a retrofitting technique for unreinforced masonry structures that is commonly applied in the Netherlands to repair settlement-induced damage. Using this technique, the bed joints of masonry walls are reinforced with steel rebars that are embedded in a high strength repair mortar. Due to the increase of induced seismic events in the northern part of the Netherlands, an experimental study was carried out at Delft University of Technology to investigate the performance of this retrofitting technique for combined settlement and seismic loading. This paper aims to simulate the experimental results, with a focus on the comparison of different finite element modelling approaches for studying both un-strengthened and strengthened full-scale tested walls. To that end, three different models are investigated – comprising both macro (continuum) and simplified and detailed micro (brick-to-brick) modelling approaches. The bricks and mortar joints are modelled as one homogenous continuum in the macro model, whereas in the two brick-to-brick models these structural components are modelled separately, with the detailed model including interface elements to simulate the brick–mortar bonds. Nonlinear pushover analyses are subsequently carried out using all three modelling approaches, for both monotonic and cyclic loading cases. Based on these analyses, the detailed brick-to-brick model was found unsuitable to simulate the strengthened wall because cracks in the model mainly occur in the form of opening of the brick–mortar bond interfaces, while smeared cracking in the plane stress elements of the mortar joints is very limited. Similarly, the continuum damage model was found to be inaccurate when pre-existing damage in the experiment needed to be taken into account. The continuum damage model also showed lower axial stresses in the rebars, compared with the simplified brick-to-brick model, as the former does not allow for the direct assignment of material properties for the high strength repair mortar in the strengthened joints.

Combined Finite-Discrete Element Model Simulations of Shake-Table Tests on a Full-Scale Masonry Cross Vault

Modeling Shake-Table Tests of a Masonry Cross Vault Through the MADY Code

Dynamic Progressive Collapse Response of Multi-Storey Frame Structures with Masonry Infills

Pre- and post-simulations of shake-table tests on a stone masonry building aggregate using finite-discrete elements

Modelling of the Dynamic Response of a Full-Scale Masonry Groin Vault: Unstrengthened and Strengthened with Textile-Reinforced Mortar (TRM)

Comparison of Continuous and Discrete Modeling Strategies for the Structural Assessment of a Masonry Vault Under Dynamic Seismic Loading

Simulation Of Collapse Process Of Masonry Walls Based On Expanded Discrete Element Method

Shaking Table Testing of an Unstrengthened and Strengthened with Textile Reinforced Mortar (TRM) Full-Scale Masonry Cross Vault

Shake-Table Testing of a Brick Masonry Groin Vault: Overview of Blind Predictions and Postdictions and Comparison with Experimental Results

3D hybrid modelling approach combining the finite and discrete element methods: Validation based on masonry shear wall tests

DEM Analysis of Masonry Open Vaults with Square Bays

Shaking table tests on a full-scale unreinforced and IMG-retrofitted clay brick masonry barrel vault

Numerical homogenization‐based seismic assessment of an English‐bond masonry prototype: Structural level application

Nonlinear Behavior of a Masonry Subassemblage Before and After Strengthening with Inorganic Matrix-Grid Composites

A Mesoscale Modelling Approach Coupling SBFEM, Continuous Damage Phase-Field Model and Discrete Cohesive Crack Model for Concrete Fracture

Simulation of Masonry Wall using Concrete Damage Plasticity Model

Discrete Element Modeling of the Seismic Behavior of Masonry Construction

A macro modelling continuum approach with embedded discontinuities for the assessment of masonry arch bridges under earthquake loading

In-Plane Lateral Response of a Full-Scale Masonry Subassemblage with and without an Inorganic Matrix-Grid Strengthening System

Comparative numerical study to simulate masonry with bed joint reinforced repointing

Finite Element Study on the Shear Capacity of Traditional Joints between Walls Made of AAC Masonry Units