Abstract:The study results of introduction of barium-strontium carbonatite of various fractional composition into flux based on silicomanganese production slag are presented. The principal possibility of using their mixtures for depositing and welding of low-alloy steels is shown, while the use of barium-strontium carbonatite makes it possible to reduce contamination of weld metal with nonmetallic inclusions. In series of experiments in laboratory conditions, various compositions of welding fluxes were made and investigated. As components, barium-strontium modifier BSC produced by “NPK Metallotechnoprom” LC under TU 1717-001-75073896-2005 was used, wt. %: 13.0 – 19.0 % BaO; 3,5 – 7,5 % SrO; 17.5 – 25.5 % CaO; 19.8 – 29.8 % SiO2 ; 0.7 – 1.1 % MgO; 2.5 – 3.5 % K2O; 1.0 – 2.0 % Na2O; 1.5 – 6.5 % Fe2O3 ; 0 to 0.4 % MnO; 1.9 – 3.9 % of Al2O3 ; 0.7 – 1.1 % TiO2 ; 16.0 – 20.0 % CO2 as well as silicomanganese slag produced by JSC “EVRAZ – West-Siberian Metallurgical Combine”, wt. %: 6.91 – 9.62 % Al2O3 ; 22.85 – 31.70 % CaO; 46.46 – 48.16 % SiO2 ; 0.27 – 0.81 % FeO; 6.48 – 7.92 % MgO; 8.01 – 8.43 % MnO; 0.28 – 0.76 % F; 0.26 – 0.36 % Na2O; up to 0,62 % K2O; 0.15 – 0.17 % S; 0.01 % P. Basis of the flux is silicomanganese production slag, into which a flux additive was introduced. Flux additive was produced in two ways. The first one: by mixing barium-strontium modifier with liquid glass in a ratio of 75 and 35 %, respectively. The second variant is as follows: dust of strontium-barium modifier of fraction less than 0.2 mm was used as a flux additive. The technology of flux-additive manufacturing is described. Welding of rollers was carried out using ASAW-1250 welding tractor. Regimes of surfacing were worked out. The chemical compositions of fluxes, slag crusts, flux and weld metal were determined. Metallographic studies of metal were performed. The results of analysis for presence of nonmetallic inclusions in weld zone were carried out in accordance with GOST 1778 – 70. Studies indicate a decrease in contamination of weld metal by silicates that are not deformed and absence of brittle silicates.

Identification of the Composition of Granular Domain Slag by IR Fourier Spectroscopy

Developing an Indexing Methodology for Estimating the Reactivity of Slag from Different Sources Use in Alkali-Activated Materials

Experimental Determination of Slag Emissivities for Enhanced Slag Control by Infrared‐Based Systems

Slag Analysis as a Method for the Characterization and Provenancing of Ancient Iron Objects

Selection of basic components of slag-forming mixture for single-step removal of impurities from cast iron

Determination of eight components in converter slag by X-ray fluorescence spectrometry

Chemical characterizations of different sized mineral-rich particles in fine slag from Entrained-flow gasification

New EAF Slag Characterization Methodology for Strategic Metal Recovery

Investigations on Physical and Chemical Properties of High Silica Sand, Fe-Cr Slag and Blast Furnace Slag for Foundry Applications

Characterization of Ladle Furnace Slag from Carbon Steel Production as a Potential Adsorbent

Electron microprobe technique for the determination of iron oxidation state in silicate glasses

Applications of Fourier-Transform IR Spectroscopy to Comprehensive Analysis of Sedimentary Rocks

Chemometrics Applied Quantitative Analysis of Iron Oxide Mixtures by Terahertz Spectroscopy.

Characterisation of the Grain Morphology of Artificial Minerals (EnAMs) in Lithium Slags by Correlating Multi-Dimensional 2D and 3D Methods

Calibration of the Composition of Low-Alloy Steels by the Interval Partial Least Squares Using Low-Resolution Emission Spectra with Baseline Correction

APPLICATION OF BARIUM-STRONTIUM CARBONATITE FOR PRODUCTION OF WELDING FLUXES BASED ON SILICOMANGANAZE PRODUCTION SLAG

Determination of Fe3O4 Content and Total Nonhydraulic Minerals in Steel Slag

Features of the Microstructure and Chemical Compositions of Vanadium-Containing Slags Including Determination of Vanadium Oxidation Degrees

CRITERIA AND MODELS FOR FORECASTING THE DISTRIBUTION COEFFICIENTS OF ELEMENTS IN THE «METAL-SLAG» SYSTEM IN OUT-OF-FURNACE STEEL PROCESSING

Determination of the Mineral Composition of the Lake Bottom Sediments by X-Ray Diffraction Method and Physico-Chemical Modelling

Characterization of a Chromium-Bearing Carbon Steel Electric Arc Furnace Slag after Magnetic Separation to Determine the Potential for Iron and Chromium Recovery