Abstract:Utilizing low-rank coals in power plants takes a risk of slagging, especially when burning coals rich in alkali and alkaline earth metallic (AAEM) elements. To predict the slagging propensity of low-rank coals, this work develops a novel approach for accurately measuring the sticking probability of thermally stable slag samples based on the well-controlled flat-flame system. We collect deposit samples (PSD) severely accumulated on the platen superheater surface of a 660 MW boiler co-firing two low ranks (alkali-rich Phi-coal: iron-rich Ind-coal = 15.2 wt%: 84.8 wt%). It is found that the existing theoretical models can hardly reproduce the measured sticking probability at elevated temperatures. We thus propose an Sshaped nonlinear correlation of ash sticking probability with the melt fraction using two tuning parameters. The fully-sintered PSD slag is mainly composed of refractory anorthite (CaAl 2 Si 2 O 8 ) and hematite (Fe 2 O 3 ), which are largely determined by the dominant Ind-coal ash fed into the boiler. However, the excessive accumulation of PSD can only be attributed to the much stickier Phi-coal ash rich in lowmelting-point, dispersed Na-aluminosilicates. Combining the measured sticking probability and physicochemical properties of the slag and ash samples, we reveal a positive correlation of the ash sticking probability with the sodium content of the samples, almost regardless of the contents of alkaline earth metals and iron. It highlights the leading role alkali metals play in slagging. In contrast, iron exists as discrete hematite (Fe 2 O 3 ) in the slag and is less effective than AAEM in forming slags on the platen superheater. Our work provides a more reliable method and criterion for evaluating the slagging propensity of fully/partially-molten particles in solid fuel combustion. (c) 2021 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Developing an Indexing Methodology for Estimating the Reactivity of Slag from Different Sources Use in Alkali-Activated Materials

Evaluation on Reactivity of Fly Ash from Different Sources in Alkali Activated System-Progressing Environmentally Construction Through Waste Utilization

Activity index for steel slag

The Study on the Interface Reaction Characteristics of Different Binary Slag, CaO – MgO, Al 2 O 3 – CaO, Al 2 O 3 – MgO, SiO 2 – CaO, SiO 2 - MgO

Prediction Model for SiO2 Activity in the CaO-Al2O3-SiO2-MgO Quaternary Slag System

Properties, Microstructure Development and Life Cycle Assessment of Alkali-Activated Materials Containing Steel Slag under Different Alkali Equivalents

A New Method to Predict Final Products of Red Mud-Slag-Based Alkali-Activated Materials Using Complete Phase Analysis of Precursors

Strength Analysis and Optimization of Alkali Activated Slag Backfills Through Response Surface Methodology

Mechanistic Studies on the Slagging Propensity in Low-Rank Coal Combustion

Mathematical model for design of optimized multi-component slag for electroslag remelting

In situ quasi-elastic neutron scattering study on the water dynamics and reaction mechanisms in alkali-activated slags

A Novel Methodology to Quantify the Slag Protective Effect on the Oxidation Behavior of Oxide‐C Refractories

Link between the Reactivity of Slag and the Strength Development of Calcium Aluminate Cement

Study on the finely ground steel slag as high reactivity blending materials of cement

STUDY ON SLAGGING BEHAVIOR DISTINGUISHING INDEX FOR BIOMASS FUEL BURNING IN THE FLUID BED

Evaluation of slagging characteristics for microalgae and lignocellulose: A comparison of aggregative index and model

Orthogonal Experimental Study on the Factors Affecting the Mechanical Properties of Alkali-Activated Slag Materials

A new method for evaluating the melting performance of the slag

Impact of Ca, Al, and Mg on reaction kinetics, pore structure, and performance of Fe‐rich alkali‐activated slag

Interaction Mechanism between Slags and Alkali Silicate Activators: An Approach Based on the Al Phases

Effect of slag basicity on the interfacial wetting behavior between CA6 refractories and CaO–SiO2–MgO–Al2O3 based slag