Abstract:The development of high-power fuel cells could advance the electrification of the transportation sector, including marine and air transport. Liquid-fueled fuel cells are particularly attractive for such applications as they obviate the issue of fuel transportation and storage. Herein, we report a direct methanol hydrogen peroxide fuel cell (DMHPFC) for high-power propulsion applications that delivers 0.8 W cm 2 peak power density by using a pH gradient-enabled microscale bipolar interface (PMBI) to effectively meet the incongruent pH requirements for methanol oxidation/peroxide reduction reactions. DMHPFCs are an important alternative to hydrogen-fed polymer electrode membrane fuel cell (PEMFCs) and anion exchange membrane fuel cells (AEMFCs) due to methanol’s high energy density compared to that of hydrogen and superior kinetics of hydrogen peroxide reduction reaction as compared to Oxygen. A unit volume of Hydrogen gas stored at a pressure of approximately 69 MPa corresponds to volume-specific energy density of roughly 2.1 kWh/l while 39% volume of aqueous methanol and 41% volume of aqueous hydrogen peroxide corresponds to volume-specific energy density of 9.2 kWh/l. So, DMHPFC’s energy density is approximately four times higher than hydrogen fuel cell’s energy density and is comparable to gasoline which contains roughly 9.2 kWh/l of available bond energy. The theoretical potential for Methanol oxidation reaction (MOR) in basic medium is lower than that in an acidic medium (-0.78 V vs. -0.02 V) and the theoretical potential for the Hydrogen peroxide reduction reaction (HPRR) is higher than that for oxygen reduction (1.77 V vs. 1.23 V in acidic medium). This results in the highest theoretically possible cell voltage for cells with alkaline anodes and acidic cathodes. We achieved sustained operation of the DMHPFC with an alkaline anode and an acidic cathode by incorporating our pH-gradient-enabled microscale bipolar interface (PMBI). However, the system exhibits a relatively low Faradaic efficiency of 50% due to the parasitic evolution of O 2 by the decomposition of H 2 O 2 . The O 2 evolution results in a mixed potential at the cathode due to the occurrence of both the HPRR (E 0 = 1.77 V versus standard hydrogen electrode [SHE]) and the oxygen reduction reaction (ORR); (E 0 = 1.23 V versus SHE), lowering the overall cell potential. The O 2 surface coverage reduces the available sites for the HPRR, effectively deactivating the catalyst. Electrocatalysts exhibiting a combination of high HPRR activity and selectivity (by inhibiting H 2 O 2 decomposition, and hence inhibiting ORR) would result in higher faradic efficiency and have been the subject of sustained interest. Here, we examine an alternate reactant-transport engineering approach to improve the overall cell potential and cell performance of the DMHPFC. Our reactant-transport engineering approach has examined the impact of reactant flowrate, flow velocity, residence time, and flow regime (via the Reynolds number ([Re]) on DMHPFC performance. Balancing the competing demands of high residence time to improve Hydrogen peroxide reduction reaction (HPRR) rates with high flowrates to detach adsorbed O 2 , we identify a critical Re and Damkholer number (Da) to efficiently exclude O 2 gas bubbles while maintaining large current densities during the operation of a DMHPFC. Reactant-transport engineering of the cathode flow field architecture and fuel flowrates mitigates parasitic hydrogen peroxide decomposition and oxygen reduction reactions and lessens cathode passivation by oxygen bubbles. DMHPCs fulfilling these criteria provide a power density of >500 mW cm -2 at 1.0 V compared to state-of-the-art polymer electrolyte membrane fuel cells (PEMFCs) that typically operate at 0.75 V. The high peak power density of 800 mW cm -2 at 1.1 V may offer a pathway to reduce fuel cell stack size for propulsion applications. Our work paves the way for such other liquid fuel cells with hydrogen peroxide as the oxidant and enabled with PMBI resulting in significantly improvement in the performance. Figure 1

Enhancement of efficiency and power output of hydrogen fuelled proton exchange membrane (PEM) fuel cell using oxygen enriched air

Effect of oxidant quantity and humidification temperature on performance of PEMFC with twin inlet and twin outlet flow field

In-Depth Understanding of Oxygen Transfer in the Catalyst Layer of High-Temperature Proton Exchange Membrane Fuel Cells

Effect of humidification of reactive gases on the performance of a proton exchange membrane fuel cell

The Performance Improvement of Membrane and Electrode Assembly in Open-Cathode Proton Exchange Membrane Fuel Cell

Study on the influence of the hydrogen–oxygen stoichiometric ratio on the power performance improvement in a large-scale PEMFC stack

Air Oxidation of Carbon Supports Boosts the Low-Humidity Fuel Cell Performance

Air flow and pressure optimization for air supply in proton exchange membrane fuel cell system

Air Bleeding Strategies to Increase the Efficiency of Proton Exchange Membrane Fuel Cell Stationary Applications Fuelled with CO ppm-levels

Boosting the Performance of Low-Platinum Fuel Cells Via a Hierarchical and Interconnected Porous Carbon Support.

CO-tolerance behaviors of proton exchange membrane fuel cell stacks with impure hydrogen fuel

Effect of air depletion in the preferential oxidation reactor and fuel depletion in a proton exchange membrane fuel cell system fueled by natural gas

Catalyst Degradation Mitigation and Fuel Utilization Enhancement of a Dead-Ended Anode and Cathode Proton Exchange Membrane Fuel Cell with Periodical Oxygen Supply

Improved Performance of Fuel Cell with Proton-Conducting Glass Membrane

Preparation of Oxygen Reduction Catalyst Electrodes by Electrochemical Acidification and Synergistic Electrodeposition

High-Performance Hydroxide Exchange Membrane Fuel Cells Through Optimization of Relative Humidity, Backpressure and Catalyst Selection

Performance Enhancement of Air-Breathing Proton Exchange Membrane Fuel Cell Through Utilization of an Effective Self-Humidifying Platinum–carbon Catalyst

Experimental study on current density distribution characteristics in a novel oxygen recirculation system of dead-ended proton exchange membrane fuel cell

Enhancing heat dissipation and mass transfer of oxygen gas flow channel in a proton exchange membrane fuel cell using multiobjective topology optimization

Experimental Analysis of Optimal Performance for a 5 Kw PEMFC System

Reactant Transport Engineering Approach at Cathode to High Power Direct Methanol Hydrogen Peroxide Fuel Cell