Abstract:<p>Due to the elimination of 'land/channel' geometry in conventional bipolar plates, metal foam as flow distributor in proton exchange membrane fuel cell (PEMFC) has shown great potential in improving the uniformity of reactant and temperature distributions, which is beneficial to the performance enhancement of the fuel cell. However, the arrangement of metal foam which can be optimized to further enhance the performance of PEMFC has not been considered yet. In the study, nickel metal foam is used as a new type of flow field for experimental research, and compared with the performance of conventional graphite parallel flow field (case 1) in a PEMFC. With respect to the arrangement of metal foam, three cases, namely the use of metal foam either in the anode side (case 2) or cathode side (case 3), and the simultaneous use of metal foam in both sides (case 4), were designed. Experimental results showed that nickel metal foam flow field can make the temperature distribution at the membrane more uniform, which is conducive to the durability of the membrane, and improves the fuel utilization rate. By comparing with case 1 at fully humidified condition, the increase of maximal power density for case 2 is 15.67 %, which is higher than case 3 (6.36 %) and case 4 (9.09 %), indicating the importance of the arrangement of metal foam. The interpretation is that when relative humidity (RH) is high, the cathode side using nickel metal foam flow field is more prone to flooding. Furthermore, a 3-hour constant current test on case 1–4 indicated that at RH = 1, a serious voltage deterioration was observed after 105 min when nickel metal foam is used in the cathode side. With the decrease of RH, the critical flooding time was gradually postponed. This finding is especially useful for the practical applications of metal foam as flow distributor in a PEMFC.</p>

Experimental study on current density distribution characteristics in a novel oxygen recirculation system of dead-ended proton exchange membrane fuel cell

Experimental study of voltage uniformity and stability of H 2 /O 2 PEM fuel cell stack with dead-end anode and recirculation cathode

Optimization strategies to mitigate reactant starvation in a dead-ended hydrogen–oxygen proton exchange membrane fuel cell during cyclic loading

Experimental investigation of operating characteristics of proton exchange membrane fuel cell with different anode strategies based on the segmented cell

Numerical simulation on purge strategy of proton exchange membrane fuel cell with dead-ended anode

Experimental performance investigation on the arrangement of metal foam as flow distributors in proton exchange membrane fuel cell

Current density and temperature distribution measurement and homogeneity analysis for a large-area proton exchange membrane fuel cell

Two-Dimensional simulation of purge processes for dead-ended H 2 /O 2 proton exchange membrane fuel cell

Dynamic evolutions of local current density and water–gas distribution of proton exchange membrane fuel cell with dead-ended anode

Performance Evaluation and Degradation Mechanism for Proton Exchange Membrane Fuel Cell with Dual Exhaust Gas Recirculation

Numerical Analysis of Parallel Flow Fields Improved by Micro-Distributor in Proton Exchange Membrane Fuel Cells

Modeling and Dynamic Performance Research on Proton Exchange Membrane Fuel Cell System with Hydrogen Cycle and Dead-Ended Anode

Study on Voltage Clamping and Self-Humidification Effects of Pem Fuel Cell System with Dual Recirculation Based on Orthogonal Test Method

Water management and structure optimization study of nickel metal foam as flow distributors in proton exchange membrane fuel cell

Performance enhancement in a H2/O2 PEMFC with dual-ejector recirculation

Improved flow field design for air-cooled proton exchange membrane fuel cells

Numerical Study of Water Transport and Operating Strategy for Fuel Cells with Segmented Water Management Flow Fields

Droplet Dynamics in a Proton Exchange Membrane Fuel Cell with Ejector-Based Recirculation

High-stability dead-end anode proton exchange membrane fuel cells by purge optimization

Performance analysis and dynamic characteristics of a proton exchange membrane fuel cell with dual recirculation pumps for air-free applications

Catalyst Degradation Mitigation and Fuel Utilization Enhancement of a Dead-Ended Anode and Cathode Proton Exchange Membrane Fuel Cell with Periodical Oxygen Supply