Abstract:Developing a high-strength, flame-resistant structural material derived from wood is desirable for advanced applications in the transportation, construction, automotive, and aerospace sectors. Here, a low-cost and high-efficiency top-down method was designed for processing natural wood veneers into lightweight yet strong bulk structural wood-based composites. The composites were produced using delignified wood veneers as a continuous reinforcing material and epoxy resin as the adhesive, followed by hot pressing. Densification of the veneers and good adhesion among the veneers played a pivotal role in the mechanical performance of the composites. A record-high flexural strength of 436.1 MPa and a toughness of 12.3 MJ·m–3 were achieved. Furthermore, the low density of the wood composite led to a specific flexural strength of 323.0 MPa·cm3·g–1, which is significantly greater than those reported for other wood-based composites and some metal materials (e.g., steels and alloys). We also explored the feasibility of using the composite in unmanned drones. In addition, the delignified wood veneers were infiltrated with 1.5% ammonium polyphosphate (APP), which improved the fire-retardant and self-extinguishing properties of the composites. This work demonstrates that high-strength wood products exhibit significant potential in many applications.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acssuschemeng.0c09390.Molding process of DWLC-41.4% with different shapes (Figure S1); delignified wood panels with different lignin removal contents (Figure S2); thickness swelling (24 h) (Figure S3); SEM images of DWLC-0%, DWLC-23.2%, and DWLC-55.1% (Figure S4); micro-CT images (Figure S5); tensile and flexural strength of DWLC-41.4% with and without epoxy resin (Figure S6); photographs of wood veneer pull-out tests: before (left) and after (right) (Figure S7); bonding strength of wood veneer and epoxy resin (Figure S8); microstructure of fracture surfaces of pure epoxy resin (Figure S9); compressive strength of natural birch wood and DWLC-41.4% (Figure S10); mechanical properties and microstructures of DWLCs with and without flame retardant (Figure S11); TG curves of DWLC, 1.5% APP/DWLC, and 2.5% APP/DWLC (Figure S12); mass loss of DWLC, 1.5% APP/DWLC, and 2.5% APP/DWLC after the cone test (Figure S13); TSR curves of DWLC, 1.5% APP/DWLC, and 2.5% APP/DWLC (Figure S14); XPS spectra of P of 1.5% APP/DWLC and 2.5% APP/DWLC (Figure S15); comparison of TTI between DWLC-41.4% and other wood-based composites (Table S1); and XPS analysis of the external char of DWLC-41.4% with and without flame retardant (Table S2) (PDF)Takeoff process of an unmanned drone (Movie S1) (MP4)This article has not yet been cited by other publications.

Advancement and challenges in sample preparation for Atomic Force Microscopy and Infrared Microscopy for wood‐based materials

Hygro-mechanical short-term behaviour of selected coatings: experiments and material modelling on vapour permeability and mechanical properties

Effects of different incising pretreatments in improving permeability in two refractory wood species

Visualization of the Stimuli-responsive Surface Behavior of Functionalized Wood Material by Chemical Force Microscopy

Influence of force volume indentation parameters and processing method in wood cell walls nanomechanical studies

Sample preparation methods for optimal HS-AFM analysis: Duplex stainless steel

Large-scale and high-resolution visualization of static mechanical properties of wood-adhesive interphase utilizing nanoindentation mapping

Influence of Wood Surface Preparation on Roughness, Wettability and Coating Adhesion of Unmodified and Thermally Modified Wood

Water Permeability and Adhesion Strength of Bio-based Coating Applied on Wood

Quantitative Analysis of Gross Adhesive Penetration in Wood Using Fluorescence Microscopy

Use of X-ray computed tomography for real-time studies of the fire progress in wood

Techniques for high resolution imaging of wood structure: a review

Laminating Delignified Wood Veneers toward High-Strength, Flame-Retardant Composites for Structural Applications

Characterization of wood-adhesive bonds in wet conditions by means of nanoindentation and tensile shear strength

Microstructure and Hydrophobic Properties of Nano-Cu-Coated Wood-Based Composites by Ultrasonic Pretreatment

Microspectroscopy as applied to the study of wood molecular structure

Sample preparation procedures for biological atomic force microscopy

Engineering of material properties by adhesive selection at the example of a novel structural wood material

Evaluation of the antifungal efficiency of coatings on wood

Small-Angle Neutron Scattering as a New Tool to Evaluate Moisture-Induced Swelling in the Nanostructure of Chemically Modified Wood Cell Walls*

Development and application of a 3D image analysis strategy for focused ion beam – Scanning electron microscopy tomography of porous soft materials