Abstract:Abstract The performance of adhesive-hardwood bonds can often be sensitive to humidity and temperature variation. Therefore, it is frequently challenging to achieve standard requirements for structural applications. To gain a better understanding of the wood-adhesive bond, the properties of the individual constituents as well as the local interface of European beech ( Fagus sylvatica L.) wood cell walls in contact with structural adhesives were analyzed by means of nanoindentation. These results are compared to classical lap-shear strength. As adhesives two different one-component polyurethane adhesives (1C PUR) and a phenol resorcinol formaldehyde adhesive (PRF) were used. In one case, the beech wood was additionally pre-treated with an adhesion-promoting agent (primer) prior to bonding with 1C PUR. Beech wood joints were analyzed subsequent to several treatments, namely standard climate, after wet storage and in re-dried conditions. In addition, the influence of the primer on the hydroxyl accessibility of beech wood was investigated with dynamic vapor sorption (DVS). The lap-shear strength revealed good performance in dry and re-dried conditions for all adhesives on beech. Both polyurethane adhesives obtained deficits when tested in wet conditions. The use of a primer significantly improved the PUR performance in wet condition. DVS experiment demonstrated a decrease in hydroxyl group accessibility when using a high primer concentration. As novelty, nanoindentation was used for the first time to characterize the local wood–adhesive-interface properties in wet conditions. Nanoindentation showed that all tested 1C PUR perform quite similar in room climate, while PRF achieves considerable higher values for reduced E-modulus and hardness. Wet storage led to a considerable reduction in mechanical properties for all adhesives, while the highest relative change was observed for PRF. After re-drying, the adhesives re-gained a large part of their original mechanical properties in room climate. No distinct effect of the primer on the local micromechanical properties could be detected with nanoindentation in terms of specific work of indentation.

Quantitative Analysis of Gross Adhesive Penetration in Wood Using Fluorescence Microscopy

Effects of different incising pretreatments in improving permeability in two refractory wood species

Adhesive Penetration in Beech Wood Part I: Experiments

Assessing Adhesion and Glue-Line Defects in Cold-Pressing Lamination of Glubam

Adhesive penetration in Beech wood Part II: Penetration Model

Transforming interface properties of wood laminate composites functionalized by adhesive penetration

Large-scale and high-resolution visualization of static mechanical properties of wood-adhesive interphase utilizing nanoindentation mapping

Comparison of methods to characterize the penetration of hot melt adhesive into paper

Characterization of wood-adhesive bonds in wet conditions by means of nanoindentation and tensile shear strength

Investigations on the Characterization of Various Adhesive Joints by Means of Nanoindentation and Computer Tomography

Small-Angle Neutron Scattering as a New Tool to Evaluate Moisture-Induced Swelling in the Nanostructure of Chemically Modified Wood Cell Walls*

Comparative Adhesive Bonding of Wood Chemically Modified with Either Acetic Anhydride or Butylene Oxide

The effect of moisture on the mechanical response of wood, adhesive and their interphase by means of nanoindentation

Effect of Phenol Formaldehyde Resin Penetration on the Quasi-Static and Dynamic Mechanics of Wood Cell Walls Using Nanoindentation

Phenol formaldehyde adhesives formulated for advanced X-ray imaging in wood-composite bondlines

Fluorescence microscopy characterization of the bonding interface of scrimbers made of alkali-treated finely fluffed poplar veneers

MALDI ToF Investigation of the Reaction of Soy Protein Isolate with Glutaraldehyde for Wood Adhesives

Understanding the mechanical strength and dynamic structural changes of wood-based products using X-ray computed tomography

Advancement and challenges in sample preparation for Atomic Force Microscopy and Infrared Microscopy for wood‐based materials

Kinetic analysis of phenol–formaldehyde bonded wood joints with dynamical mechanical analysis

Engineering of material properties by adhesive selection at the example of a novel structural wood material