Abstract:The unique properties of silicon oxide materials, no matter intrinsic or doped, utilized in thin film solar cells (TFSCs) in the area of photovoltaic (PV) are making TFSCs one of the most attractive photovoltaic technologies for the development of high-performing electricity production units to be integrated in everyday life. In comparison to other silicon materials, the particular diphasic structure of silicon oxide materials, in which hydrogenated microcrystalline silicon (μc-Si:H) crystallites are surrounded by an oxygen-rich hydrogenated amorphous silicon (a-Si:H) phase, causes them present excellent photoelectrical material properties, such as a low-parasitic absorption in the broadband spectral range, independent controllability of longitudinal and lateral conductivity, refractive indices (3.5-2.0), band gap (2.0-2.6 eV) and conductivity tenability (with orders of 1-10-9 S/cm) with oxygen doping, and so on. Various types of silicon oxide materials, including intrinsic, p- or n- type, further applied in TFSCs have also played significant roles in improving the efficiency of various types of single-, dual-, and triple-junction thin-film solar cells from both the optical and electrical points of view. In this paper, we present our latest progress in studying the performance improvement role of intrinsic or doped silicon oxide materials in pin-type a-Si:H, a-SiGe:H, and μc-Si:H single-junction solar cells. By effectively tuning the band gap values of intrinsic a-SiOx:H materials with oxygen doping and adopting the layers with a suitable band gap (1.86 eV) as the P/I buffer layers of a-Si:H solar cells fabricated on metal organic chemical vapor deposition (MOCVD) boron-doped zinc oxide (ZnO:B) substrates, a significant Voc increases up to 909 mV and an excellent external quantum efficiency (EQE) response of 75% at the 400 nm typical wavelength can be achieved by matching the band gap discontinuity between the p-type nc-SiOx:H window and a-Si:H intrinsic layers. The serious leakage current characteristics of pin-type narrow-gap (Eg<1.5 eV) a-SiGe:H single-junction solar cells can also be finely tuned by integrating an n-type μc-SiOx:H layer with a small oxygen content in addition to improving the long-wavelength response, an effective approach gives rise to the highest FF of 70.62% for pin-type a-SiGe:H single-junction solar cells with an average band gap of 1.48 eV. In addition, our studies proved that the application of p-type μc-SiOx:H window layers in μc-Si:H single-junction solar cells can effectively improve the short-wavelength light coupling by suppressing the parasitic absorption and promoting the anti-reflectivity with a graded refractive index profile. On the basis of the optimum single-junction solar cells with omnipotent silicon oxide materials, an initial efficiency of 16.07% has been achieved for pin-type a-Si:H/a-SiGe:H/μc-Si:H triple-junction solar cells with an active area of 0.25 cm2. The omnipotent properties of silicon oxide layers in TFSCs, including effective optical coupling and trapping, suitability in compensating for the band gap discontinuity, the shunt-quenching capacity, and so on, make them likely to be extended to other types of solar cells such as polycrystalline chalcopyrite Cu(In,Ga)Se2 (CIGS) and perovskite-sensitized solar cells, opening up new opportunities for acquiring solar cells with higher performance.

Inter-atomic diffusion of fluorine and oxygen forming electron-selective extraction for high-efficiency dopant-free silicon solar cells

One‐Step Formation of Low Work‐Function, Transparent and Conductive MgFxOy Electron Extraction for Silicon Solar Cells

Modulation of the TCO/MoO x Front Contact Enables >21% High-Efficiency Dopant-Free Silicon Solar Cells

Self‐Diffusion Effect Assisted TiO2/Li3PO4 Electron Selective Passivating Contact in Silicon Solar Cells Approaching 23% Efficiency

A High-Quality Dopant-Free Electron-Selective Passivating Contact Made from Ultra-Low Concentration Water Solution

Low Oxygen Content MoOx and SiOx Tunnel Layer Based Heterocontacts for Efficient and Stable Crystalline Silicon Solar Cells Approaching 22% Efficiency

Simulation of Silicon Heterojunction Solar Cells for High Efficiency with Lithium Fluoride Electron Carrier Selective Layer

Electron‐Selective Strontium Oxide Contact for Crystalline Silicon Solar Cells with High Fill Factor

< 50-μm thin crystalline silicon heterojunction solar cells with dopant-free carrier-selective contacts

Boost Organic‐Silicon Hybrid Solar Cell Performances with a Facile and Cost‐effective Sub‐3 nm Interface Control Method

Interfacial engineering of ZnS passivating contacts for crystalline silicon solar cells achieving 20% efficiency

Advanced Functional Materials: Intrinsic and Doped Silicon Oxide

Prelithiation-coupled defluorination polymerization for constructing LiF-rich oligomers interface for highly stable SiO anode

Principles of dopant-free electron-selective contacts based on tunnel oxide/low work-function metal stacks and their applications in heterojunction solar cells

Highly Efficient and Highly Flexible Thin Crystalline Silicon Heterojunction Solar Cells Based on Dopant-Free Carrier-Selective Contacts Fabricated with Simple Processes

Interphasial Pre-lithiation and Reinforcement of Micro-Si Anode through Fluorine-free Electrolytes

Controlled defects and enhanced electronic extraction in fluorine-incorporated zinc oxide for high-performance planar perovskite solar cells

LiTFSI-Free Hole Transport Materials for Robust Perovskite Solar Cells and Modules with High Efficiencies.

Constructing tin oxides Interfacial Layer with Gradient Compositions for Efficient Perovskite/Silicon Tandem Solar Cells with Efficiency Exceeding 28%

Li, Ag Co‐Doping Enables Efficient Kesterite Solar Cell with a High Fill Factor of 74.30%

High-Mobility Hydrogenated Fluorine-Doped Indium Oxide Film for Passivating Contacts c-Si Solar Cells