Abstract:Considering the abundance of iron and manganese within the Earth's crust, the cathode O3-NaFe0.5Mn0.5O2 has shown great potential for large-scale energy storage. Following the strategy of introducing specific heteroelements to optimize the structural stability for energy storage, the work has obtained an O3-type NaFe0.4Mn0.49Cu0.1Zr0.01O2 that exhibits enhanced electrochemical performance and air stability. It displays an initial reversible capacity of 147.5 mAh g–1 at 0.1C between 2 and 4.1 V, a capacity retention ratio exceeding 69.6% after 100 cycles at 0.2C, and a discharge capacity of 70.8 mAh g–1 at a high rate of 5C, which is superior to that of O3-NaFe0.5Mn0.5O2. The codoping of Cu/Zr reserves the layered O3 structure and enlarges the interlayer spacing, promoting the diffusion of Na+. In addition, the structural stability and air stability observed by Cu-doping is well maintained via the incorporation of extra Zr favoring a highly reversible phase conversion process. Thus, this work has demonstrated an efficient strategy for developing cobalt/nickel-free high-capacity and air-stable cathodes for sodium-ion batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12684.Rietveld refinement for the XRD pattern of NFMC-0.1 cathode sample; SEM imaging for all the codoped cathode samples, SEM imaging for three cathode samples treated by water immersion; the cyclic curves and the charge–discharge profiles for the codoped cathode samples; the initial charge–discharge curves of NFMCZ-0.01 in different voltage ranges; in situ XRD patterns of NFMCZ-0.01; charge–discharge curves for the three cathode samples after water immersion treatment; the survey spectrum for the codoped cathode sample NFMCZ-0.01 (Figures S1–S8); refined crystal parameters for NFM, NFMC-0.1, and NFMCZ-0.01 by single-phase simulation; comparison of cyclic stability between the previous relevant literature and this work (Tables S1–S4); and detailed procedure to make GITT analysis (PDF)This article has not yet been cited by other publications.

A novel air‐stable O3‐type layered oxide cathode material with low Ni content for sodium‐ion batteries

La-doped O3-type Layered Oxide Cathode with Enhanced Cycle Stability for Sodium-Ion Batteries

High Energy Density Sodium‐Ion Battery with Industrially Feasible and Air‐Stable O3‐Type Layered Oxide Cathode

Design of Cu-Substituted O3-Type NaFe0.5 Mn0.5 O2 Cathode Materials for Sodium-Ion Batteries

A Novel Ni-rich O3-Na[Ni0.60Fe0.25Mn0.15]O2 Cathode for Na-ion Batteries

Facile design and synthesis of Co-free layered O3-type NaNi0.2Mn0.2Fe0.6O2 as promising cathode material for sodium-ion batteries

Copper and Zirconium Codoped O3-Type Sodium Iron and Manganese Oxide as the Cobalt/Nickel-Free High-Capacity and Air-Stable Cathode for Sodium-Ion Batteries

High stability of Cu-doped O3-type NaNi1/3Fe1/3Mn1/3O2 cathode material for sodium-ion battery

Boosting fast ionic transport and stability of O3-NaNi1/3Fe1/3Mn1/3O2 cathode via Al/Cu synergistically modulating microstructure for high-rate sodium-ion batteries

O3-NaNi0.47Zn0.03Mn0.5O2 cathode material for durable Na-ion batteries

Air-Stable High-Entropy Layered Oxide Cathode with Enhanced Cycling Stability for Sodium-Ion Batteries

A high-rate and air-stable cathode material for sodium-ion batteries: yttrium-substituted O3-type Ni/Fe/Mn-based layered oxides

Enhanced Cyclability of O3-NaNi 0.33 Fe 0.31 Mn 0.36 O 2 by Mg and Cu Synergistic Doping with Strengthened Mn-O Bonds

A Universal Strategy toward Air‐Stable and High‐Rate O3 Layered Oxide Cathodes for Na‐Ion Batteries

Trace Ti/Mg Co-Doped O3-type Layered Oxide Cathodes with Enhanced Kinetics and Stability for Sodium-Ion Batteries

Sodium-deficient O3-type Na0.83Cr1/3Fe1/3Mn1/6Ti1/6O2 As a New Cathode Material for Na-ion Batteries

Interlayer substitution enables air-stable and long-life O3-type cathode for sodium-ion batteries

Stabilized O3‐Type Layered Sodium Oxides with Enhanced Rate Performance and Cycling Stability by Dual‐Site Ti4+/K+ Substitution

High-entropy configuration of O3-type layered transition-metal oxide cathode with high-voltage stability for sodium-ion batteries

Defensive and Ion Conductive Surface Layer Enables High Rate and Durable O3‐type NaNi1/3Fe1/3Mn1/3O2 Sodium‐Ion Battery Cathode

NASICON-Type NaTi2(PO4)3 Surface Modified O3-Type NaNi0.3Fe0.2Mn0.5O2 for High-Performance Cathode Material for Sodium-Ion Batteries.