Abstract:Powder-fed laser additive manufacturing (LAM) based on directed energy deposition (DED) technology is used to produce S316-L austenitic, and S410-L martensitic stainless steel structures by 3D-printing through a layer-upon-layer fashion. The microstructural features and crystallographic textural components are studied via electron backscattering diffraction (EBSD) analysis, hardness indentation and tensile testing. The results are compared with commercial rolled sheets of austenitic and martensitic stainless steels. A well-developed <math><200></math> direction solidification texture (with a J-index of ∼11.5) is observed for the austenitic structure produced by the LAM process, compared to a J-index of ∼2.0 for the commercial austenitic rolled sheet. Such a texture in the LAM process is caused by equiaxed grain formation in the middle of each layer followed by columnar growth during layer-upon-layer deposition. A quite strong preferred orientation (J-index of 17.5) is noticed for martensitic steel developed by LAM. Large laths of martensite exhibit a dominant textural component of <math>{011}<111></math> in the α-phase, which is mainly controlled by transformation during layer-by-layer deposition. On the other hand, the martensitic commercial sheet consists of equiaxed grains without any preferred orientation or completely random orientations. In the case of the austenitic steel, mechanical properties such as tensile strength, hardness and ductility were severely deteriorated during the LAM deposition. A ductility loss of about 50% is recorded compared to the commercially rolled sheets that is attributed to the cast/solidified structure. However, LAM manufacturing of martensitic stainless steel structures leads to a considerably enhanced mechanical strength (more than double) at the expense of reduced ductility, because of martensitic phase transformations under higher cooling rates.

Effect of Laser Traverse Speed on the Metallurgical Properties of Fe-Cr-Si Clads for Austenitic Stainless Steel Using Directed Energy Deposition

Effect of processing parameters on the microstructure of laser-clad Stellite 6 on the X19CrMoNbVN11-1 stainless-steel substrate

Effects of scanning speed on the microstructure, hardness and corrosion properties of high-speed laser cladding Fe-based stainless coatings

Effect of in-situ Transverse Magnetic Field on Microstructure, Mechanical Properties and Corrosion Resistance of the Directed Energy Deposited 316 L Stainless Steel

Effect of Interlayer Temperature on the Formation Characteristics and Microstructure Evolution of the 304 Stainless Steel Fabricated by-CMT Directed Energy Deposition-Arc Manufacturing

Influence of Scanning Speed on Microstructure and Properties of Laser Cladded Fe-Based Amorphous Coatings

Optimization of Laser Metal Deposition Process for 2205 Duplex Stainless Steel

Metallurgical and Electrochemical Properties of Super Duplex Stainless Steel Clads on Low Carbon Steel Substrate produced with Laser Powder Bed Fusion

Effect of laser cladding speed on microstructure and properties of titanium alloy coating on low carbon steel

Effect of Scanning Speed on Microstructure and Properties of Laser Cladding Fe‐0.3C‐15Cr‐1Ni High Hardness Corrosion‐Resistant Alloy Coating on 3Cr13 Surface

Electromagnetic Coupling Field Effect on Microstructure and Wear Behavior of Laser-Clad 304 Stainless Steel

Laser Directed Energy Deposition of Bulk 316L Stainless Steel

Deposition of Nickel-Based Superalloy Claddings on Low Alloy Structural Steel by Direct Laser Deposition

Effects of laser additive manufacturing on microstructure and crystallographic texture of austenitic and martensitic stainless steels

Revealing the Evolution of Microstructure and Mechanical Properties with Deposition Energy and Shielding Gas to Achieve Phase-Balanced Directed Energy Deposition of 2205 Duplex Stainless Steel

A new laser remelting strategy for direct energy deposition of 316L stainless steel

Effect of Carbon Content of Substrate on the Microstructure Changes and Tensile Behavior of Clad Layer of Stainless Steel Composites

Effect of closed-loop controlled melt pool width on microstructure and tensile property for Fe-Ni-Cr alloy in directed energy deposition

Microstructural evolution and corrosion properties of Fe-based amorphous coating by laser cladding on 316L stainless steel

Microstructure Characterization and Properties of Laser Cladding Forming 316L Stainless Steel

The role of substrate preheating on the microstructure, roughness, and mechanical performance of AISI 316L produced by directed energy deposition additive manufacturing