Abstract:Recently, laser additive manufacturing (LAM) of Al–Mg–Sc–Zr alloys has been considered an important method for developing a new generation of high-performance Al alloys. However, one of the key differences between LAM and conventional casting/wrought processes is that it has a unique combination of rapid solidification and in-situ solid-state transformation induced by repeated thermal cycling during deposition. In addition, owing to its near-net shape characteristics, subsequent plastic deformation processing is typically not an option to improve the as-built microstructure. To gain insight into the effect of the complex thermal history during LAM on the microstructural evolution and mechanical properties of the novel alloy systems, an Al–Mg–Sc–Zr alloy was processed via laser-directed energy deposition (L-DED) using a substrate with air cooling (AC) or water cooling (WC). The results show that the solidification microstructure was closely related to the dynamic solidification conditions in the molten pool, which promoted the transition from an equiaxed grain structure at low cooling rate (AC) to a heterogeneous grain structure at high cooling rate (WC). Furthermore, in-situ precipitation occurred during the repeated high-temperature thermal cycling in the AC sample, while it was effectively suppressed in the WC sample by lowering the peak temperature during thermal cycling. After aging, the yield strength of the WC sample was enhanced to ∼2 times that of the AC sample, while the uniform elongation was still comparable to that of the AC sample. To achieve good mechanical properties for L-DED-processed Al–Mg–Sc–Zr alloys, it is crucial to conduct integrated control of the thermal history during both rapid solidification and in-situ precipitation.

Effect of closed-loop controlled melt pool width on microstructure and tensile property for Fe-Ni-Cr alloy in directed energy deposition

Pore defects and corrosion behavior of AISI 316L stainless steel fabricated by laser directed energy deposition under closed-loop control

Effect of laser incident energy on the densification and structure–property relationships of additively manufactured CrCoNi medium-entropy alloy

Improved wear resistance of directed energy deposited Fe-Ni-Cr alloy via closed-loop controlling laser power

Integrated Control of Thermal Residual Stress and Mechanical Properties by Adjusting Pulse-Wave Direct Energy Deposition

Effects of Ultrasonic Vibration on Microstructure and Mechanical Properties of 1Cr12Ni3MoVN Alloy Fabricated by Directed Energy Deposition

The microstructural evolution and mechanical response of laser direct energy deposition Inconel 718 alloy based on simulation and experimental methods

Influence of pulsed laser scanning patterns on microstructural evolution and mechanical properties of Inconel 718 in direct laser deposition

Multi-regional Microstructure Control Using Ultrasonic-Assisted Directed Energy Deposition for Al-Cu Alloy

Molten pool characteristics of a nickel-titanium shape memory alloy for directed energy deposition

Numerical simulation on melt pool and solidification in the direct energy deposition process of GH3536 powder superalloy

Thermal-fluid behavior, microstructure and mechanical properties in liquid bridge transfer mode during directed energy deposition-arc additive manufacturing – Insights using NiTi as a model alloy

Anisotropic dynamic compression response of an ultra-high strength steel fabricated by laser hybrid additive manufacturing

Tailoring material microstructure and property in wire-laser directed energy deposition through a wiggle deposition strategy

Composition fine-tuning for directed energy deposition of Ti-6Al-4V

Directed energy deposition additive manufacturing of a Sc/Zr-modified Al–Mg alloy: Effect of thermal history on microstructural evolution and mechanical properties

Process-induced Mechanical Property Heterogeneity along the Building Direction of Directed Energy Deposited IN718 Thin-walled Parts

Evolution of microstructure and mechanical properties in the molten pool of γ-TiAl alloy synthesized in situ by dual-wire-fed electron beam directed energy deposition.

Integrated control mechanism of ultrasound and ZrO2 particles on differential microstructures for the wire arc additive manufacturing

Evolution of microstructure and mechanical property of Ti-47Al-2Cr-2Nb intermetallic alloy by laser direct energy deposition: From a single-track, thin-wall to bulk

Investigation of the Influence of Process Parameters on Crack Formation and Mechanisms in Ti-48Al-2Cr-2Nb Alloy via Laser Directed Energy Deposition