Abstract:A SiO2/Al/LiNbO3 structure has a large electromechanical coupling factor (K2) and good temperature coefficient of frequency (TCF) for the UMTS Band I application. However, the SiO2/Al/LiNbO3 structure also supports two unwanted spurious responses; one is caused by the Rayleigh mode and the other by the transverse-mode. As the authors have previously discussed, the Rayleigh-mode spurious response can be suppressed by controlling the cross-sectional shape of a SiO2 overlay deposited on resonator electrodes. On the other hand, the transverse-mode spurious responses are commonly suppressed by IDT (Interdigital Transducer) apodization, and the length weighting for dummy electrodes selectively could scatter higher order transverse-mode spurious responses. In this paper, the spurious responses of the SAW resonator on a SiO2/Al/LiNbO3 structure are analyzed by the laser probe system. And, a new technique to suppress the transverse-mode spurious responses is proposed. In the technique, the SiO2 overlay is selectively removed from the dummy electrode region. The transverse-mode spurious behavior was dependent on the velocities (vi and vd) in the IDT and the dummy regions. When vi <; vd, the higher-order transverse-mode spurious response could be suppressed. Furthermore, the SAW energy confinement could be enhanced in the IDT electrode region by selectively SiO2 removing. The transverse-mode spurious responses were successfully suppressed without degrading the SAW resonator performances.

AlN/Al0.8Sc0.2N film S0 mode lamb wave resonator with spurious mode suppression

Spurious-Free S1 Mode AlN/ScAlN-Based Lamb Wave Resonator With Trapezoidal Electrodes

Analysis and Suppression of Spurious In-Plane Lamé-Like Modes in Lamb Wave Resonators

AlN/ScAlN composite films-based spurious free A1 mode lamb wave resonator with adjustable effective electromechanical coupling coefficient

High performance SAW resonator with spurious mode suppression using double-layer electrode transverse modulation

High Figure-of-Merit A1-Mode Lamb Wave Resonators Operating Around 6 GHz Based on the LiNbO3 Thin Film

High Electromechanical Coupling Factor Lamb Wave Resonator

4.9 GHz A<inf>1</inf>-mode Lamb Wave Resonator based on Partially Released LN Film

Ultra flexible pseudo-lamb wave RF resonators based on ZnO/PI and AlN/PI structures

Suppression of Transverse-Mode Spurious Responses by Selectively SiO2 Removing Technique for SAW Resonators on a SiO2/Al/LiNbO3 Structure

Ultralow Acoustic Loss Micromachined Butterfly Lamb Wave Resonators on AlN Plates

High speed surface acoustic wave and laterally excited bulk wave resonator based on single-crystal non-polar AlN film

Investigation of Spurious Mode Suppression in 3.8 GHz Shear-Horizontal Mode Surface Acoustic Wave Resonators Based on LiNbO3/SiO2/Si Multilayer Structure

Investigation on spurious mode suppression in 3.8-GHz SH-mode SAW resonators based on LiNbO 3 /SiO 2 /Si multilayer structure

Transducer design for AlN Lamb wave resonators

High Q‐factor Anapole Mode Based on Localized Spoof Surface Plasmon Polaritons

Study on the impact of the resonant cavity and lateral acoustic edge reflector for AlSc 0.095 N-based S0 mode Lamb-wave resonators

Suppression of Transverse-Mode Spurious Responses for Saw Resonators on Sio2/Al/Linbo3 Structure by Selective Removal of Sio2

Adjustable effective electromechanical coupling of Lamb wave resonator using AlN/Sc0.096Al0.904N composite films

6 GHz lamb wave acoustic filters based on A1-mode lithium niobate thin film resonators with checker-shaped electrodes

Aln Checker-Mode Resonators With Routing Structures