Abstract:The high entropy alloys (HEAs) of dual FCC have great potential for semi-solid processing. Therefore, at temperatures of 1130–1225 °C and strain rates of 0.1–10 s −1 isothermal deformation, semi-solid thixotropic behavior and microstructure evolution of the deformed CoCrCu 1.2 FeNi HEA were investigated by scanning electron microscopy (SEM), differential scanning calorimetry (DSC), optical microscopy (OM), and electron backscattered diffraction (EBSD). The results show that the original billet is a deformed microstructure consisting of dual FCC structure. The alloy exhibits a typical stress-strain curve at the low strain rate. When the strain rate is larger than 0.5 s −1 , the stress-strain curves show two peaks. The apparent viscosity decreases with an increase of shear rate and deformation temperature, indicating that the shear thinning effect occurs. Semi-solid compression leads to uneven plastic deformation. According to the degree of plastic deformation, the sample is divided into hard deformation zone, large deformation zone, transition deformation zone and free deformation zone. The flow stresses, liquid phase fraction and deformation mechanisms of the solid particles can lead to variations in the microstructure of the different zones. The roundness of the grains increases and then decreases as the temperature rises, while the grain size fluctuates in the large deformation zone. Phase structure is not changed during semi-solid deformation, but it can weaken the segregation of Cu at low temperatures and low strain rates during isothermal deformation. The strain rate is the main factor affecting recrystallization, the degree of recrystallization increases with increasing temperature at low strain rates, and a large amount of deformation microstructure is produced at high strain rates.

Solidification simulation of single-phase Fe–Co–Cr–Ni–V high entropy alloy

Solidification Simulation and Experimental Validation of Single-Phase Fe–Co–Cr–Ni–V–Al High-Entropy Alloy

Microstructural evolution and phase selection during solidification of AlCrCuFeNi high entropy alloy

Study on Precipitation in (cocrfemnni)90al6ti4 High Entropy Alloy

Integrated experimental and modeling approach for hot deformation behavior of Co-Cr-Fe-Ni-V High Entropy Alloy

Semi-solid thixotropic behavior and microstructure evolution of cold deformed CoCrCu 1.2 FeNi high-entropy alloy

Realizing strength-ductility combination of Fe3.5Ni3.5Cr2MnAl0.7 high-entropy alloy via coherent dual-phase structure

Phase equilibria in equiatomic CoCuFeMnNi high entropy alloy

Microstructure of and mechanical properties of an as-cast fine-grain dual-phase Fe-based high entropy alloy formed via solid-state phase transformation

Microstructure characterization and phase evolution of equiatomic AlCoMoFeNi high entropy alloy synthesized by mechanical alloying

Evaluation of the impact of Mn and Al on the microstructure of Fe–Co–Ni–Cr based high entropy alloys

Microstructure and mechanical properties of Al0.4Co0.5V0.6FeNi high-entropy alloys processed by homogenization treatment

Microstructure and mechanical properties of non equiatomic FeCoNiCuMo high entropy systems

Influence of Cu and Co addition on metallurgical and wear characteristics of AlCrFeNi high entropy alloy

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Evolution of phase stability and structural properties in CrFeNiTiV high-entropy alloy under high-temperature heat treatment conditions

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Understanding the physical metallurgy of the CoCrFeMnNi high-entropy alloy: an atomistic simulation study

Electron beam melting of (FeCoNi)86Al7Ti7 high-entropy alloy

Microstructural Study of CrNiCoFeMn High Entropy Alloy Obtained by Selective Laser Melting

Microstructure, mechanical properties and corrosion resistance of an as-cast fine-structured Cr-Fe-Ni-Al-Si high entropy alloy