Abstract:Lead may cause a series of health problems which ranged from behavioral problems, learning disabilities to seizures or even death. The conventional treatment methods adopted for removing lead from wastewater included chemical precipitation, electro-chemical reduction, ion exchange process and adsorption method. However, these methods had certain disadvantages, such as high cost, technical sophistication, generation of sludge, or other waste products that needed to be processed. Therefore, it was necessary to research and develop a treatment method which had the advantage of relative high efficiency and low operating cost. On the basis of above considerations, an emerging lead removal system, namely, the catalyzed internal electrolysis based on advanced ferric-carbon filler, was applied to treat lead-containing wastewater, especially the lead pollution water in rural areas. To investigate the effect of catalyzed internal electrolysis based on advanced ferric-carbon filler treating water that simulated lead pollution in rural area, this study adopted single factor experimental design and orthogonal experimental design that included eight factors and three levels, making study on initial pH(1.0~8.0), reaction time(10-90 min) and aeration quantity(0-12 L/h). The results showed that the removal rate of Pb2+rose slowly at first and then dropped sharply when pH value rose from1.0 to 8.0. The removal rate of Pb2+rose steadily when the reaction time increased from 10 min to 60 min and tended to be stable when the reaction time kept extending to 90 min. The removal rate of Pb2+rose sharply at first and then dropped slowly when aeration quantity increased from 0 to 12 L/h. The influence of the three factors on removal efficiency of Pb2+were as follows: aeration quantity>initial pH value>reaction time, the best reaction condition occurred when the initial pH value was at 3.0, the reaction time was 60 min and aeration quantity was 6L/h. This paper fitted the reaction stage according to the first-order kinetic model, observed the surface feature and structure changes of the ferric-carbon filler before and after the reaction by using scanning electron microscope (SEM) and analyzed the components of solution after the reaction by using X-ray diffraction (XRD) and inferred that the mechanism for catalyzed internal electrolysis removing lead was oxidation-reduction and chemical precipitation. In optimum experimental conditions, the concentration of Pb2+could fall to 0.037 mg/L after treatment when initial Pb2+concentration was 1.0 mg/L, which could meet the requirement on limiting value of the case-Ⅲ water specified in Environment Quality Standards for Surface Water (GB3838-2002). This research results may provide theoretical foundation and design basis for the remediation of the lead pollution water in rural areas.

Optimization of the electrocoagulation process for the removal of lead from water using aluminium as electrode material

Removal of chromium (VI) and lead from synthetic solution using electrocoagulation: optimization and performance study

Treatment of contaminated river water by batch electrocoagulation system using aluminium and iron electrodes: Performance of process and statistical analysis

Enhancing lead ion removal from simulated wastewater through continuous electrocoagulation process: investigating operating parameters and adsorption behavior

Research on a new electrochemical method combined with chemical coagulation in removal of lead, zinc, and copper from wastewater

Electrocoagulation removal of Pb, Cd, and Cu ions from wastewater using a new configuration of electrodes

A hybrid system for lead removal of simulated battery industry Wastewater using electrocoagulation/electroflotation

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

Treatment of industrial electroplating wastewater for metals removal via electrocoagulation continous flow reactors

Techno-economic evaluation of electrocoagulation for cattle slaughterhouse wastewater treatment using aluminum electrodes in batch and continuous experiment

Electrokinetic removal of aluminum and chromium from industrial wastewater electrocoagulation treatment sludge

Development of electrocoagulation process for wastewater treatment: optimization by response surface methodology

Comparison of the Removal Efficiencies for Electro-Flotation and Electrocoagulation Wastewater Treatment Methods to Treat Effluents Discharged from Electroplating Industries

Study on characteristics of catalyzed internal electrolysis treating simulated rural lead pollution water

Arsenic Removal from Contaminated Drinking Water by Electrocoagulation Using Hybrid Fe–Al Electrodes: Response Surface Methodology and Mechanism Study

Operating parameters optimal scheme and feasibility research of enhancing strategies for electro-kinetic remediation on lead-polluted estuary sediments treatment

Electrocoagulation in treatment of municipal wastewater– life cycle impact assessment

Electrocoagulation in a packed aluminium scraps anode reactor for mineral processing wastewater treatment

The Study of Lead Removal from Aqueous Solution Using an Electrochemical Method with a Stainless Steel Net Electrode Coated with Single Wall Carbon Nanotubes

Removal of chromium (VI) and lead from electroplating effluent using electrocoagulation

Removal of chemical oxygen demand and ammonia nitrogen from lead smelting wastewater with high salts content using electrochemical oxidation combined with coagulation–flocculation treatment