Abstract:Abstract A real industrial electroplating rinsing wastewater was collected and subjected to physical and chemical examination. The study showed that it can be categorized as high strength wastewater, at pH- 2, COD 1430 mg/l, and high level of metals above permissible limits, namely: 150, 30, 25, and 2.9 for Ni, Cu, Zn, and Fe mg/l respectively. Therefore, metals must be adequately removed before discharging to avoid any hazardous impact on the environment. Similar synthetic wastewater was prepared to study the effect of chemical coagulation for the precipitation of metals. The optimum removal rate was achieved by using a combination of lime and ferric chloride at 100 and 30 mg/l respectively. The chemically treated electroplating wastewater was subjected to an electrocoagulation study. A comparison between iron and stainless-steel electrodes for the removal of metals was investigated. Furthermore, the effect of different electric voltages, and contact time on metals removal efficiency were also examined. It was found that the optimum removal capacity was achieved when a stainless steel electrode was employed in the presence of ferric chloride as coagulant, at 10 volts, 30 min. contact time, and pH 9 for synthetic solution. In a batch treatment system, the real industrial wastewater was treated at the predetermined optimum operating conditions; the removal of metals was 92.1%, 87.8% and 82.9% for Ni. Zn, and Cu respectively. By employing a continuous flow reactor for the treatment of the same real wastewater and under the same operating conditions, metals removal rate increased to 98.9%, 97.4% and 96.6% for Ni. Zn, and Cu respectively. The level of metals in the final treated wastewater copes with Egyptian Environmental Regulation. The overall results confirmed that the electro-coagulation (EC) technology offers an effective alternative process in combination with the conventional chemical coagulation process for reaching high removal performance of toxic metals from the electroplating wastewater. The advantage of EC technique is achieving high treatment efficiency instead of expensive chemical reagents, high construction cost and/or other conventional processes. In addition, the final treated water can be reused for rinsing process in the electroplating industry and/or discharging without any environmental hazard effect. It is also recommended to employ solar energy instead of electricity to reduce cost of operation.

Electrocoagulation in a packed aluminium scraps anode reactor for mineral processing wastewater treatment

Electrochemical Oxidation of Chemi-Thermo-mechanical Pulping Wastewater

A Combined Electrocoagulation-Electrooxidation Treatment on Ctmp Wastewater

ELECTROCHEMICAL TREATMENT OF RECIRCULATING AQUACULTURE WASTEWATER USING A Ti/RuO2-IrO2 ANODE FOR SYNERGETIC TOTAL AMMONIA NITROGEN AND NITRITE REMOVAL AND DISINFECTION

Electrocoagulation removal of Pb, Cd, and Cu ions from wastewater using a new configuration of electrodes

Electrochemical behavior of aluminium anode in super-gravity field and its application in copper removal from wastewater by electrocoagulation

Efficient removal of NaOl from mineral processing wastewater using Al-electrocoagulation

Phosphate Removal Efficiency and Life Cycle Assessment of Different Anode Materials in Electrocoagulation Treatment of Wastewater

Evaluation of scrap metallic waste electrode materials for the application in electrocoagulation treatment of wastewater

Electrolysis-enhanced coagulation process for highly emulsified oily wastewater treatment: Floc diameter, oil removal performance and mechanism

Removal of chemical oxygen demand and ammonia nitrogen from lead smelting wastewater with high salts content using electrochemical oxidation combined with coagulation–flocculation treatment

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

Electrokinetic removal of aluminum and chromium from industrial wastewater electrocoagulation treatment sludge

Treatment of Ni-EDTA containing wastewater by electrocoagulation using iron scraps packed-bed anode

Intensification of a new electrocoagulation system characterized by minimum energy consumption and maximum removal efficiency of heavy metals from simulated wastewater

Electrocoagulation pre-treatment to simultaneously remove dissolved and colloidal substances and Ca2+ in old corrugated container wastewater

Electrocoagulation-based wastewater treatment process and significance of anode materials for the overall improvement of the process: A critical review

Treatment of industrial electroplating wastewater for metals removal via electrocoagulation continous flow reactors

Improved Electrocoagulation Reactor for Rapid Removal of Phosphate from Wastewater

Treatment of electroplating wastewater using electrocoagulation and integrated membrane

Optimization of an integrated electrodisinfection/electrocoagulation process with Al bipolar electrodes for urban wastewater reclamation