Abstract:Abstract A real industrial electroplating rinsing wastewater was collected and subjected to physical and chemical examination. The study showed that it can be categorized as high strength wastewater, at pH- 2, COD 1430 mg/l, and high level of metals above permissible limits, namely: 150, 30, 25, and 2.9 for Ni, Cu, Zn, and Fe mg/l respectively. Therefore, metals must be adequately removed before discharging to avoid any hazardous impact on the environment. Similar synthetic wastewater was prepared to study the effect of chemical coagulation for the precipitation of metals. The optimum removal rate was achieved by using a combination of lime and ferric chloride at 100 and 30 mg/l respectively. The chemically treated electroplating wastewater was subjected to an electrocoagulation study. A comparison between iron and stainless-steel electrodes for the removal of metals was investigated. Furthermore, the effect of different electric voltages, and contact time on metals removal efficiency were also examined. It was found that the optimum removal capacity was achieved when a stainless steel electrode was employed in the presence of ferric chloride as coagulant, at 10 volts, 30 min. contact time, and pH 9 for synthetic solution. In a batch treatment system, the real industrial wastewater was treated at the predetermined optimum operating conditions; the removal of metals was 92.1%, 87.8% and 82.9% for Ni. Zn, and Cu respectively. By employing a continuous flow reactor for the treatment of the same real wastewater and under the same operating conditions, metals removal rate increased to 98.9%, 97.4% and 96.6% for Ni. Zn, and Cu respectively. The level of metals in the final treated wastewater copes with Egyptian Environmental Regulation. The overall results confirmed that the electro-coagulation (EC) technology offers an effective alternative process in combination with the conventional chemical coagulation process for reaching high removal performance of toxic metals from the electroplating wastewater. The advantage of EC technique is achieving high treatment efficiency instead of expensive chemical reagents, high construction cost and/or other conventional processes. In addition, the final treated water can be reused for rinsing process in the electroplating industry and/or discharging without any environmental hazard effect. It is also recommended to employ solar energy instead of electricity to reduce cost of operation.

Removal of chromium (VI) and lead from synthetic solution using electrocoagulation: optimization and performance study

Removal of chromium (VI) and lead from electroplating effluent using electrocoagulation

Optimization of the electrocoagulation process for the removal of lead from water using aluminium as electrode material

Electrocoagulation removal of Pb, Cd, and Cu ions from wastewater using a new configuration of electrodes

Economic and performance evaluation of electrocoagulation unit for the treatment of hexavalent chromium using Taguchi method

Removal of chromium from tannery industry wastewater using iron-based electrocoagulation process: experimental; kinetics; isotherm and economical studies

Simultaneous removal of Cr(VI) and Cu(II) from acid wastewater by electrocoagulation using sacrificial metal anodes

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

Using Electrode Electrolytes to Enhance Electrokinetic Removal of Heavy Metals from Electroplating Sludge

Electrokinetic removal of aluminum and chromium from industrial wastewater electrocoagulation treatment sludge

Enhanced chromium removal from tannery wastewater through electrocoagulation with iron electrodes: Leveraging the Box-Behnken design for optimization

Enhancing lead ion removal from simulated wastewater through continuous electrocoagulation process: investigating operating parameters and adsorption behavior

Removal of Chromium(Vi) from Wastewater by Combined Electrocoagulation-Electroflotation Without A Filter

Batch Electrocoagulation Process for Removal of Chromium from Tannery Wastewater

Treatment of industrial electroplating wastewater for metals removal via electrocoagulation continous flow reactors

Sustainability of Electrocoagulation Process in the Removal of Dicofol Pesticide using Aluminium Electrodes

Research on a new electrochemical method combined with chemical coagulation in removal of lead, zinc, and copper from wastewater

Separation of Chromium(VI) Metal in Wastewater Using Electrocoagulation Method with NaCl Coagulant

Removal of hexavalent chromium from electroplating wastewater by ion-exchange in presence of Ni(II) and Zn(II) ions

Electrolysis of Metal Coating Industrial Waste Using Carbon Electrode to Reduce Metal Levels of Chromium (Cr), Zink (Zn), and Cadmium (Cd)

THE TREATMENT OF Cr6+ CONTAINING WASTEWATER BY Fe/C MICRO-ELECTROLYSIS SYSTEM