Abstract:Flow softening behavior, microstructure evolution and hot working parameters of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy were systematically studied by isothermal hot compression. Based on the analysis of processing maps and the corresponding microstructure, power dissipation efficiency peak occurred at two domains, which were associated with dynamic recrystallization (DRX) and super-plasticity. Pile-up of high density dislocation and a large number of twins were the primary deformation mechanisms at low temperature and high strain rate. As the temperature increases, fine DRX grains promote the movement and rotation of grain boundary, the softening of β phase and the transformation of β→α/α2+γ above 1200 °C improve the deformation capacity of the alloy significantly. Crack-free TiAl sheets were successfully obtained by direct hot rolling process at 1080 °C and 1220 °C. The corresponding microstructure and mechanical properties were analyzed. The sheets rolled at 1080 °C was characterized by near γ (NG)+β0 microstructure with a streamline along the rolling direction, while duplex (DP)+β0 microstructure appeared to be the main microstructure at rolling temperature of 1220 °C. The as-rolled sheet exhibits excellent mechanical properties at 800 °C. The sheet rolled at 1080 °C exhibits 320 MPa yield strength and 468 MPa ultimate tensile strength with 142% elongation. The yield strength, ultimate tensile strength, and elongation of the as-rolled sheet are 446 MPa, 586 MPa, and 3.0%, respectively, when rolled at 1220 °C. The excellent ductility of the sample rolled at 1080 °C is attributed to formation of fine DRX grains due to consumption of twins and substructure under tensile stress, which promote grain boundary slip. Lamellar colonies with fine interlamellar spacing and α2 laths formed at 1220 °C can effectively prevent dislocation motion, resulting in a significant increase in the strength of the alloy.

Development of Ti–V–Mo Complex Microalloyed Hot-Rolled 900-MPa-Grade High-Strength Steel

Research on Microstructure and Property of Hot-Rolled 700MPa Grade Automobile Sheet

Microstructure, Precipitation and Mechanical Properties of a Titanium-Tungsten Alloyed Hot Rolled High Strength Steel

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Precipitation behavior of Ti–Nb–V–Mo quaternary microalloyed high strength fire-resistant steel and its influence on mechanical properties

The microstructure evolution and tensile properties of Ti–43Al–4Nb–1Mo-0.2B alloy during hot rolling

Precipitation of MC Phase and Precipitation Strengthening in Hot Rolled Nb–Mo and Nb–Ti Steels

Microstructural Characteristic of Low Carbon Microalloyed Steels Produced by Thermo-Mechanical Controlled Process

Development of high strength plates with low yield ratio by the combination of TMCP and inter-critical quenching and tempering

Microstructure Evolution and Mechanical Properties of a Hot-Rolled Ti Alloy

Quantitative analysis of precipitation and strengthening mechanisms of V and V-Ti hot-rolled microalloyed steels

Microstructure and Properties of a Low Carbon Ti-V Microalloyed Steel

Comparison of Novel 1 GPa Low‐Carbon, Low‐Alloyed Steel Produced with Simulated and Laboratory‐Scale Thermomechanical Controlled Processes

Rolling parameters, microstructure control, and mechanical properties of powder metallurgy Ti–44Al–3Nb-(Mo, V, Y) alloy: The impact of rolling temperatures

Microstructure and Mechanical Properties of a New TWIP Steel under Different Heat Treatments

Multiphase precipitation behavior and tensile properties of a Fe-Mn-Al-Mo-C austenitic lightweight steel

Effect of intercritical annealing temperature on microstructure and mechanical properties of V-Ti-Mo microalloyed medium Mn steel

Evolution of Microstructures and Mechanical Properties During Solution Treatment of a Ti–V–Mo-containing High‑manganese Cryogenic Steel

Development and Study of High-Strength Low-Mo Fire-Resistant Steel

Variations in microstructure and mechanical properties along thickness direction in a heavy high strength low alloy steel plate

Hot deformation behavior, dynamic recrystallization mechanism and processing maps of Ti–V microalloyed high strength steel