Analysis of Ozonation Effect on Performance and Water Quality in Closed-System Cooling Tower

M. I Alhamid,R. M Miftah,M. A Rainanda

DOI: https://doi.org/10.5109/4742139

2021-12-01

Evergreen

Abstract:Online Public Access Catalog

What problem does this paper attempt to address?

The Effect of Ozonation on Particle Size Distribution for Recirculating Aquacultural Seawater: Analysis of Particle Flocculation and Breakup

Mingdong Ji,Kang Wu,Jianping Li,Zhangying Ye,Haijun Li,Songming Zhu

DOI: https://doi.org/10.1080/01919512.2019.1644993

2019-01-01

Abstract:Solids removal is very important for water quality maintenance in recirculating aquaculture systems (RAS). Ozonation is a practical water treatment which can promote the solids removal. However, the characteristics of ozonation effects on particles are still unclear. In this study, the effect of ozonation on particle size distribution (PSD) was investigated for seawater from a RAS of Pacific white shrimp (Litopenaeus Vannamei). Both flocculation and breakup of particles were demonstrated during ozonation treatment, which resulted in changes of PSD. By using a fractal characteristic value (D-f), the flocculation process could be divided into three stages of preparation, growth and steady. Besides, the flocculation efficiency varied parabolically with contact time. A higher ozone dosage resulted in a shorter preparation stage, along with a longer growth stage (namely lasting a longer flocculation effect) and thus a relatively higher limit of parabolic flocculation efficiency. However, the limit would reach a peak and probably be accompanied with a more breakup of particles. The best flocculation efficiency was 43% at ozone dosage of 3.5 mg/L with 5 min contact time. Furthermore, a higher ozone dosage could produce more ammonia.
THE SIGNIFICANCE OF PROPER COOLING TOWER WATER TREATMENT: A CASE STUDY

Mohd Nadzrie Ahmad

DOI: https://doi.org/10.35631/ijirev.515012

2023-12-31

International Journal of Innovation and Industrial Revolution

Abstract:This paper presents the result of a study of the effect of cooling tower system in terms of performance and cost of maintenance. The study was conducted in a two-storey shopping complex building. Observation on site was held to obtain data on full load amp (FLA) and chilled water temperature (CWT) before and after servicing cooling tower unit. Energy of cooling tower were evaluated by analysis of FLA and CWT in percentage value. The condition on the system and component were also observed to differentiate the condition before and after treatment. The result obtained showed that cooling system performance after the treatment was increased.
Experimental and computational analysis of thermal performance of the oval tube closed wet cooling tower

Wei-Ye Zheng,Dong-Sheng Zhu,Jin Song,Li-Ding Zeng,Hong-jian Zhou

DOI: https://doi.org/10.1016/j.applthermaleng.2011.10.047

IF: 6.4

2012-03-01

Applied Thermal Engineering

Abstract:Closed wet cooling towers (CWCTs) characterize by smaller investment and exploitation cost as well as fewer materials and less space. It can be regarded as a cooling tower with the packing replaced by a bank of tubes. However, heat and mass transfer in an oval tube closed wet cooling tower (CWCT) have been little investigated under different operating conditions. The thermal performance characteristics of an oval tube CWCT were conducted. From the experimental results, correlations for the water-film heat transfer coefficient and air–water mass transfer coefficient are obtained. Experimental tests show the water-film heat transfer coefficient is a function of deluge-water temperature, deluge-water mass velocity and air mass velocity, which is different from that in the public literatures. The air–water mass transfer coefficient is a function of air mass velocity. In addition, a mathematical model with three ordinary differential functions is presented to predict the outlet process water temperature. The model is solved by a sectional method. The results show the analytical outlet temperature compares well with the experimental data. The method is suitable for evaluating the performance of an oval tube CWCT.

energy & fuels,engineering, mechanical,thermodynamics,mechanics
Effect of Different Water Quality on Ozonation of 2, 4-D

CHEN Lan,SHI Hui-xiang,WANG Da-hui

DOI: https://doi.org/10.3785/j.issn.1008-973x.2006.03.035

2006-01-01

Abstract:For investigating the effect of complex water quality on ozonation process in water treatment,an analysis method with simulated water quality in a laboratory scale reactor was presented.After different inorganic salts and small molecule organics were added to 2,4-dichlorophenoxyacetic acid(2,4-D) solution prepared with deionized water,tap water and surface water were used to prepare 2,4-D solution without other additives,and organics,chloride ion and hydrogen peroxide concentration were analyzed during the reaction process to learn the impact of water quality on kinetics of ozonation.Experimental results show that tap water,surface water and some compounds such as sodium phosphate promote ozonation kinetics rate constant and enhance the dechlorination rate of 2,4-D.Some compounds such as Sodium chloride inhibit reaction and weaken the dechlorination rate.Sodium sulfate makes no difference to the degradation of 2,4-D.Hydrogen peroxide is produced during the ozonation of 2,4-D.The hydrogen peroxide formation rate is influenced by the water quality.
THEORETICAL AND EXPERIMENTAL STUDY ON THERMAL PERFORMANCE OF CLOSED WET COOLING TOWER

Najim A. Jassim

DOI: https://doi.org/10.31026/j.eng.2011.06.27

2011-12-01

Journal of Engineering

Abstract:Thermal performance of closed wet cooling tower has been investigated experimentally and theoreticallyin this work. The theoretical model based on heat and mass transfer equations and heat and mass transfer balance equations which are established for steady state case. A new small indirect cooling tower was used for conducting experiments. The cooling capacity of cooling tower is 1 kW for an inlet water temperature of 38oC, a water mass velocity 2.3 kg/m2.s and an air wet bulb temperature of 26oC. This study investigates the relationship between saturation efficiency, cooling capacity and coefficient of performance of closed wet cooling tower versus different operating parameters such wet-bulb temperature, variable air-spray water flow ratio and cooling water inlet temperature. Results indicate that the capacity and saturation efficiency was found close to the related experimental results. Good agreement was obtained between the theoretical results and experimental measurements for the performance of small cooling tower.
Application of photoelectrochemical oxidation of wastewater used in the cooling tower water and its influence on microbial corrosion

Seenivasan Kokilaramani,Alagersamy Satheeshkumar,M. S. Nandini,Jayaraman Narenkumar,Mohamad S. AlSalhi,Sandhanasamy Devanesan,Prabhu Manickam Natarajan,Rajaram Rajamohan,Aruliah Rajasekar,Tabarak Malik

DOI: https://doi.org/10.3389/fmicb.2024.1297721

IF: 5.2

2024-03-13

Frontiers in Microbiology

Abstract:Background Cooling towers are specialized heat exchanger devices in which air and water interact closely to cool the water's temperature. However, the cooling water contains organic nutrients that can cause microbial corrosion (MC) on the metal surfaces of the tower. This research explores the combined wastewater treatment approach using electrochemical-oxidation (EO), photo-oxidation (PO), and photoelectrochemical oxidation (PEO) to contain pollutants and prevent MC. Methods The study employed electro-oxidation, a process involving direct current (DC) power supply, to degrade wastewater. MC studies were conducted using weight loss assessments, scanning electron microscopy (SEM), and x-ray diffraction (XRD). Results After wastewater is subjected to electro-oxidation for 4 h, a notable decrease in pollutants was observed, with degradation efficiencies of 71, 75, and 96%, respectively. In the wastewater treated by PEO, microbial growth is restricted as the chemical oxygen demand decreases. Discussion A metagenomics study revealed that bacteria present in the cooling tower water consists of 12% of Nitrospira genus and 22% of Fusobacterium genus. Conclusively, PEO serves as an effective method for treating wastewater, inhibiting microbial growth, degrading pollutants, and protecting metal from biocorrosion.

microbiology
Analysis of sludge ozonation efficiency and its influencing factors in bubble column

JIANG Yi-feng,HUANG Xiao-nan,WANG Zhi-bin,JIN Yun-zhen

DOI: https://doi.org/10.3969/j.issn.1000-6923.2017.09.027

2017-01-01

Abstract:In this context, a bubble column reactor was employed for sludge ozonation, where the effects of ozone concentration, sludge concentration and ozone dosage on sludge solubilization and organic release was investigated, respectively. The results showed that a high cell lysis rate was achieved but with an obvious mineralization of released COD, and it in consequence lowered the ozonation efficiency. Based on the response surface methodology, it revealed that there was interaction effects among the above influencing factors, and their respective order for sludge solubilization rate and COD release rate were: ozone concentration > sludge concentration > ozone dosage, and ozone concentration > ozone dosage > sludge concentration. Finally, the optimum operational conditions for sludge ozonation was obtained, by the related multiple quadratic regression model established and validated experimentally.
Thermal and experimental analysis of cross-flow closed cooling tower

M.A. Hassab,M. Khamis Mansour,L.A. Sadek,M.A. Qassem

DOI: https://doi.org/10.1016/j.aej.2023.02.012

2023-02-26

AEJ - Alexandria Engineering Journal

Abstract:Background Cross-flow closed cooling towers (CCCT) are an indirect-contact evaporative cooler in which ambient air, spray water, and process fluid work together. The thermal performance of this cooling tower has significant impact on the thermal performance of the system in which it is implemented. CCCT introduces considerable difficulty in its thermal analysis particularly because it has two-dimensional analysis in its heat characteristics. Methods In this work, a novel correlation between the tower effectiveness (ε) and its number of transfer units (NTU) was developed to simulate analytically the thermal performance/design of CCCT. This relationship is featured by its simplicity in use and has non-iterative procedure to be employed as the traditional one in the literature. Results The new relationship was verified through comparison with experimental work. The simulated results from the new model show a satisfactory agreement with those obtained from the our experimental work of less than ±5%, less than ±2% difference from experimental work done by Jiang et al. [8] , and with deviation of −3.89% from those obtained by Krӧger [9] . On the other hand, there is a good agreement between the present model and those obtained from the traditional ԑ-NTU method with maximum deviation of −4.56%. Conclusions These new correlations are handy to be used by the process engineer or CCCT designer and they are featured by direct input parameters and no need for iterative process.
Modeling climatic effect on physiochemical parameters and microorganisms of Stabilization Pond Performance

Alaa E Ali,Waheed M Salem,Sara M Younes,Mohammed Kaid

DOI: https://doi.org/10.1016/j.heliyon.2020.e04005

IF: 3.776

2020-05-23

Heliyon

Abstract:The present study was carried out to evaluate the relationship between physiochemical parameters, microorganisms, wastewater and climate in Stabilization Pond Performance. This study performed as a post-treatment after the secondary wastewater treatment using extended aeration in Rashid city, Egypt. The model of the extended aeration as secondary wastewater treatment was developed based on the combination with lagoon after the secondary sedimentation basin. The Climatic functions have an important impact on the mechanism of ponds as it actuates vertical mixing of the pond contents. The interaction between bacteria, algae and other organisms are the main idea of oxidation pond treatment beside the relationship between the climatic functions, physiochemical parameters and microorganisms biomass. The removal of biodegradable organic loads specially nitrogen and phosphorous are perfectly happens in oxidation maturation ponds which reflects a higher treatment efficiency of the sewage by 98%-99% of Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD) and heavy metals. The study included some recommendations aiming at improving both water quality and its recycling in plants irrigation.
Thermodynamic Investigation on the Performance of Closed Wet Cooling Tower

Jiamei Fang,Xuhui Zhao,Lin Zhang,Shi Bu,Zhikang Yu,Weigang Xu,Yiyang Hu,Yanfei Shan,Yong Li

DOI: https://doi.org/10.1115/1.4051633

2021-07-26

Journal of Thermal Science and Engineering Applications

Abstract:Abstract Closed wet cooling tower (CWCT) is an indirect-contact evaporative cooler, in which ambient air, spray water, and process water function together. In order to improve its thermal performance, a new heat transfer strategy is proposed. The influence of fan frequency, spray density, and processing water flow on the thermal performance of CWCT is obtained by combining theoretical and experimental research. By fitting the experimental data, the empirical formula of heat and mass transfer coefficient is obtained. The research results can be used to improve the cooling efficiency and enhance the heat and mass transfer of CWCT.

engineering, mechanical,thermodynamics
A novel approach for energy and mass transfer characteristics in wet cooling towers associated with vapor-compression air conditioning system by using MgO and TiO2 based H2O nanofluids

Ashraf Mimi Elsaid

DOI: https://doi.org/10.1016/j.enconman.2019.112289

IF: 10.4

2020-01-01

Energy Conversion and Management

Abstract:In hot weather, the performance attributes of the refrigeration cycles associated with cooling towers drop pointedly, and thus, the energy consumption excesses in addition to more troubles start to occur. Improve the cooling tower performance before the cooled fluid enters the condenser of the vapor compression air conditioning system (VCACS) can enhance the refrigeration cycle performance, lowering operating and maintenance cost, conserve the environment, and consequently save consumed energy. In this research, the experimental work on the performance-enhancing of a central air-conditioning utilizing cooling tower is presented under an enormous range of design and operating conditions. The purpose is to investigate the trace of several design parameters such as; nanoparticle concentration ratios, nanoparticle type, filling type, filling sheet spacing and sprayer angle whereas the operation parameters as; working fluid flow rate and air velocity on the performance characteristics for the VCACS. Two nanomaterial types being contemplated are MgO and TiO2 at varied concentrations of 0.1, 0.5, and 1.0% wt. It is found that the using of spiral sprayer with a spray angle of 90° had an effect of 106% and a 76.5% increase on the cooling tower effectiveness in comparing with a spray angle of 30°, and 150°, respectively. The maximum overall system performance index is observed at PVC fill, β = 12 mm, a nanoparticle of MgO based water, φ = 1%, and θ = 90°. Correlations of Ka.VP/ṁf and ε are predicted with its deviations using DataFit software based on the obtained experimental data.

energy & fuels,thermodynamics,mechanics
Effects of the Water Quality Maintained by Ozonation Enhanced Ecosystem in the Landscape of Reclaimed Water

Yu Demiao,Ma Jun,Bai Yu,Gan Yiping

DOI: https://doi.org/10.1109/ICEET.2009.368

2009-01-01

Abstract:The landscape of reclaimed water always broke out water bloom because of containing high concentrations of nitrogen and phosphorus. The TP and TN of the landscape decreased to 0.04 mg/L and 2.27 mg/L respectively with recycling ozonation at the end of the experiment. Chlorophyll a was 94.3 mg/m3 and CODCr was 45.1 mg/L. Ozonation could inactivate the algae but not destroy the cell completely. Comparing to the landscape of reclaimed water without ozonation, the algae reproduction was well controlled, while the quality of the landscape water was superior. Ozone could promote the biodegradability of landscape water although it could not remove algae and nutrients directly. The optimum ozone dose was 5 mg/L-10 mg/L. The maintenance techniques of recycling ozonation that improved the water quality enhanced the ecosystem of the landscape to avoid water bloom.
Experimental Study on Effect of Water Spray Characteristics on Performance of Cooling Tower

Akshay S. Dhurandhar,Amarsingh B. Kanase-Patil

DOI: https://doi.org/10.1051/e3sconf/202017001009

2020-01-01

E3S Web of Conferences

Abstract:Cooling tower is an indispensable part, used as a direct contact type heat exchanger mainly for evaporative cooling. Cooling tower generally dissipates, remove heat from thermal power plants. In an induced draft cooling tower of counter flow, used for a mini-steam power plant, hot water enters at the top, while the air is introduced at the bottom and exits at the top, air is allowed to come in contact with falling water droplets, causing evaporative cooling. A possibility of desired change with different spray angle, patterns, is tried and analysed. On findings, best suited spray nozzle angle resulted is 90°, and amongst three spray patterns, full cone, hollow cone and spiral type nozzle; full cone nozzle of 90° spray angle helps achieving efficiency up to 82%. The range increases successively from 9.8°C to 15.5°C for FC nozzle, in approach to WBT; the desirable fall of 3.56°C is attained with effectiveness of 81.63%.
Theoretical and computational analysis of closed wet cooling towers and its applications in cooling of buildings

Ala Hasan,Kai Sirén

DOI: https://doi.org/10.1016/s0378-7788(01)00131-1

IF: 7.201

2002-06-01

Energy and Buildings

Abstract:Theoretical analysis and computational modelling of closed wet cooling towers (CWCTs) are presented. Experimental measurements for performance of a prototype tower are used to define the tower transfer coefficients. Tower flow rates and number of tubes and rows are optimised for the required cooling load and to achieve a high coefficient of performance (COP). The performance of a cooling system used to cool office buildings is simulated using the transient system (TRNSYS) simulation environment. The cooling system consisted of a CWCT, chilled ceilings, pumps and a fan. A control strategy, including night cooling, is introduced in the simulation. The results indicate efficient performance and high COP values for the system.

energy & fuels,construction & building technology,engineering, civil
Effect Of The Water Inlet Temperature And Flow Rate On The Energy And Exergy Performance of A Forced Draft Counter Wet Cooling Tower

Fadhil Abdulrazzaq Kareem,Doaa Zaid Khalaf,Mustafa J. Al-Dulaimi,Yasser Abdul Lateef

DOI: https://doi.org/10.21203/rs.3.rs-612502/v1

2021-06-22

Abstract:Abstract The authors have requested that this preprint be removed from Research Square.
Studi Performa Cooling Tower berdasarkan Kualitas Air Pendingin

Endri Yani,Akmal Hadi Yurihuda Putra

DOI: https://doi.org/10.25077/inomet.1.2.39-42.2023

2023-12-29

Abstract:Cooling water is used to cool fluids with a high temperature in a closed system, such as a cooling tower or heat exchanger. Sometimes, the cooling water is specified in a long tube, which risks fouling and rusk. This research will study cooling water quality as Total Dissolved Solid (TDS), chlorine concentration, and antiscale. In the design of the cooling tower at PLTGU Tanjung Uncang, the range or limit of the permitted TDS is 50,000. If this figure has been reached, the cooling tower must be blown down. Blowdown is water in the cooling tower that is deliberately removed to avoid the concentration of impurities during heat evaporation. At PLTGU Tanjung Uncang, the permitted chlorine concentration is in the range of 0.2-0.5. Chlorine flow in the cooling tower at PLTGU Tanjung Uncang is reversed with Cl concentration and TDS. Inject Antiscale aims to maintain cooling tower performance, which aims to be anti-rust.
A survey of cooling tower water quality for condenser tube fouling potential

G J Zdaniuk,L M Chamra,P J Mago

DOI: https://doi.org/10.1243/09576509jpe437

2008-02-01

Abstract:Fouling from cooling tower water is a serious problem in both power and refrigeration industries. The effect of fouling on enhanced tubes could be worse than that on smooth tubes because fouling may degrade the superior heat transfer performance by filling the gaps between the roughness elements with foulant. Condensers that use cooling tower water usually experience four different fouling mechanisms: corrosion, scaling, particulate, and biological fouling. Corrosion is prevented with chemical inhibitors, which pacify the piping and protect the metal surfaces. Cooling tower water can also be treated with biocide to prevent biological fouling. Therefore, the current paper addresses scaling and particulate fouling. The paper also establishes a database of water quality based on chemical analysis of samples collected from cooling towers across the country. The objective of the database is to determine water qualities that are typical of those found in actual cooling towers. From chemical analysis, three water qualities were determined: having an average fouling potential, a low fouling potential, and a severe fouling potential. These water qualities can be used in experimental determinations of fouling resistances in augmented tubes.
A Desktop Assessment of Ozone Micro-Nanobubble Technology for Algae and PFAS Removal from Surface Water Bodies Using Open-Source Water Quality Data

Soheil Aber,Rachelle Aguada,Randimal Marasinghe,Christopher W. K. Chow,Raufdeen Rameezdeen,Ke Xing

DOI: https://doi.org/10.3390/su16020668

IF: 3.9

2024-01-13

Sustainability

Abstract:Ozone is an excellent oxidant and helps in breaking down both organic and inorganic compounds; this effect is further enhanced when it decomposes into hydroxyl radicals. Several studies confirm the good performance of ozonation and micro-nanobubble technology in eradicating algae and per- and poly-fluoroalkyl substances. However, very little is known about the application of ozone micro-nanobubble technology in small-scale treatment; hence, this research aims to assess the potential of this technology. A survey was performed to obtain the water quality parameters of some selected water bodies via relevant open-source databases. The water quality was compared against the Environmental Protection Authority (EPA) guidelines to identify those that did not meet the criteria and it was identified that 18% of the surface water bodies were below the recommended guidelines. The identified water sources were then used for the treatment simulation, which applies the literature-reported % removal of water quality parameters to predict the effectiveness of ozone micro-nanobubble technology for the selected water sources in this study. Furthermore, the time (dose) that is needed for the treatment using this technology was estimated based on the surface area of the water bodies. The scalability study was conducted to assess how many water bodies could be treated within a day using a 50 m3/h flow rate, which yielded a value of 27%. It was concluded that ozone micro-nanobubble technology can treat algae and per- and poly-fluoroalkyl substances in surface waters as part of their treatment process by reducing treatment frequency and environmental impacts. By observing the benefits of ozone micro-nanobubble technology, there is a considerable chance that the surface water bodies in the City of Salisbury and, therefore, other small-scale water treatment plants, will be healthier after undergoing this process. This study demonstrated the advantages of applying open-source water quality data as a quick approximation of the evaluation of new treatment techniques, which will help engineers to better predict the performance of the designed field trials.

environmental sciences,environmental studies,green & sustainable science & technology
Full-Scale Application of Catalytic Ozonation for Drinking Water Treatment: Case Study in China

Zheng-Qian Liu,Bang-Jun Han,Gang Wen,Jun Ma,Sheng-Jun Wang,Ren-Guang Zha,Li-Ping Shen,Chun Wang

DOI: https://doi.org/10.1061/(asce)ee.1943-7870.0000735

IF: 2.479

2014-01-01

Journal of Environmental Engineering

Abstract:A combination process of biofiltration, conventional treatment, catalytic ozonation and upflow biological activated carbon (BAC) is adopted for treating micropolluted raw water in Guanjinggang waterworks in China, and the present investigation mainly focuses on the effect of catalytic ozonation on the performance of BAC and on water quality over a long period of 699 days. The quality of finished water produced by the combination process is found to fully meet the drinking water standard of China. The removal efficiency of CODMn by catalytic ozonation is usually in the range of 10-20%, and this removal efficiency is independent of the CODMn concentration of the influent and water temperature. Catalytic ozonation can enhance the biodegradability of the effluent, and favors the following BAC. Catalytic ozonation also removes some ammonia and transforms organic nitrogen into NH4+-N. A slight increase of turbidity and manganese ion levels after catalytic ozonation are also found in many cases. Overall, the effectiveness of pollutant removal and the low operation cost make catalytic ozonation suitable for micropolluted raw water treatment in developing countries. (C) 2013 American Society of Civil Engineers.
Investigation of influencing factors of limit air-to-water ratio of cooling tower

Ming Xiao Jia,Junjie Yan,Tao Ning,Ming Liu,Gen Li,Shan Zheng

2011-01-01

Kung Cheng Je Wu Li Hsueh Pao/Journal of Engineering Thermophysics

Abstract:Experimental investigation was conducted on the cooling tower test device using the outlet water temperature as evaluation index. The experimental results indicated that: the outlet water temperature decreased with the increase of air-to-water ratio, but the trend was decreasing gradually. The limit air-to-water ratio existed during the decrease of outlet water temperature. The outlet water temperature had little change when the air-to-water ratio was up to this value. The limit air-to-water ratio decreased with the increase of inlet air dry bulb temperature and wet bulb temperature, and increased with the increase of inlet water temperature. And the limit air-to-water ratio decreased with the increase of the flow rate of circulating water. Such conclusions may be advantageously used in guiding the design and operation of cooling tower.

Analysis of Ozonation Effect on Performance and Water Quality in Closed-System Cooling Tower

The Effect of Ozonation on Particle Size Distribution for Recirculating Aquacultural Seawater: Analysis of Particle Flocculation and Breakup

THE SIGNIFICANCE OF PROPER COOLING TOWER WATER TREATMENT: A CASE STUDY

Experimental and computational analysis of thermal performance of the oval tube closed wet cooling tower

Effect of Different Water Quality on Ozonation of 2, 4-D

THEORETICAL AND EXPERIMENTAL STUDY ON THERMAL PERFORMANCE OF CLOSED WET COOLING TOWER

Application of photoelectrochemical oxidation of wastewater used in the cooling tower water and its influence on microbial corrosion

Analysis of sludge ozonation efficiency and its influencing factors in bubble column

Thermal and experimental analysis of cross-flow closed cooling tower

Modeling climatic effect on physiochemical parameters and microorganisms of Stabilization Pond Performance

Thermodynamic Investigation on the Performance of Closed Wet Cooling Tower

A novel approach for energy and mass transfer characteristics in wet cooling towers associated with vapor-compression air conditioning system by using MgO and TiO2 based H2O nanofluids

Effects of the Water Quality Maintained by Ozonation Enhanced Ecosystem in the Landscape of Reclaimed Water

Experimental Study on Effect of Water Spray Characteristics on Performance of Cooling Tower

Theoretical and computational analysis of closed wet cooling towers and its applications in cooling of buildings

Effect Of The Water Inlet Temperature And Flow Rate On The Energy And Exergy Performance of A Forced Draft Counter Wet Cooling Tower

Studi Performa Cooling Tower berdasarkan Kualitas Air Pendingin

A survey of cooling tower water quality for condenser tube fouling potential

A Desktop Assessment of Ozone Micro-Nanobubble Technology for Algae and PFAS Removal from Surface Water Bodies Using Open-Source Water Quality Data

Full-Scale Application of Catalytic Ozonation for Drinking Water Treatment: Case Study in China

Investigation of influencing factors of limit air-to-water ratio of cooling tower