Abstract:Abstract Microstructure control in the laser powder bed fusion additive manufacturing processes is a topic of major interest because of the submillimeter length scale at which the manufacturing process occurs. The ability to control the process at the melt pool scale allows for microstructure control that few other manufacturing techniques can match. The majority of work on microstructure control has focused on altering laser parameters to control solidification conditions (Ref (R.R. Dehoff, M.M. Kirka, W.J. Sames, H. Bilheux, A.S. Tremsin, L.E. Lowe, and S.S. Babu, Site Specific Control of Crystallographic Grain Orientation through Electron Beam Additive Manufacturing, Mater. Sci. Technol., 2014, 31 (8), p 931–938. R. Shi, S.A. Khairallah, T.T. Roehling, T.W. Heo, J.T. McKeown, and M.J. Matthews, Microstructural Control in Metal Laser Powder Bed Fusion Additive Manufacturing Using Laser Beam Shaping Strategy, Acta Mater., 2020, 184 , p 284–305, https://doi.org/10.1016/j.actamat.2019.11.053 .)). Other machine parameters, besides the laser parameters, have also been shown to affect the microstructure of AM parts (Ref (N. Nadammal, S. Cabeza, T. Mishurova, T. Thiede, A. Kromm, C. Seyfert, L. Farahbod, C. Haberland, J.A. Schneider, P.D. Portella, and G. Bruno, Effect of Hatch Length on the Development of Microstructure, Texture and Residual Stresses in Selective Laser Melted Superalloy Inconel 718, Mater. Des., 2017, 134 , p 139–150, https://doi.org/10.1016/j.matdes.2017.08.049 . F. Geiger, K. Kunze, and T. Etter, Tailoring the Texture of IN738LC Processed by Selective Laser Melting (SLM) by Specific Scanning Strategies, Mater. Sci. Eng. A, 2016, 661 , p 240–246, https://doi.org/10.1016/j.msea.2016.03.036 .)). We propose an investigation of the effects of hatch spacing and layer thickness on microstructure development in laser powder bed fusion additive manufacturing. A Monte Carlo Potts model with textured solidification capabilities is used to study the effects of these parameters on a unidirectional scan strategy. The simulation results reveal substantial changes in grain morphology as well as texture. Additionally, EVP-FFT crystal plasticity simulations were performed to evaluate the effect of the microstructural shifts on mechanical response. The conclusions from this work elucidate the effects of these parameters on part microstructure as predicted by the texture-aware solidification Potts model and inform understanding of how bulk texture is predicted by the simulation approach.

Surface tension-powered build dimension control in laser additive manufacturing process

Support Equilibrium Design for Laser Additive Manufacturing of Lightweight Component Based on Geometric Deformation Minimization

Study of the Mechanism of a Stable Deposited Height During GMAW-Based Additive Manufacturing

Part geometry and conduction-based laser power control for powder bed fusion additive manufacturing

Understanding Melt Pool Behavior of 316L Stainless Steel in Laser Powder Bed Fusion Additive Manufacturing

Influences of Laser Incidence Angle and Wall Thickness on Additive Components

A Surface Quality Optimization Strategy Based on a Dedicated Melt-Pool Control Via the Dashed-Scan Contouring Technique in Electron Beam Powder Bed Fusion

Surface morphologies of intra-layer printing process in electron beam powder bed fusion: A high-fidelity modeling study with experimental validation

Investigation of thermal and fluid dynamics behaviors of melt pool during laser direct metal deposition on inclined substrates

Microstructural control in metal laser powder bed fusion additive manufacturing using laser beam shaping strategy

Energy Coupling Mechanisms and Scaling Behavior Associated with Laser Powder Bed Fusion Additive Manufacturing

Laser incidence angle influence on energy density variations, surface roughness, and porosity of additively manufactured parts

Simulation Study of Hatch Spacing and Layer Thickness Effects on Microstructure in Laser Powder Bed Fusion Additive Manufacturing using a Texture-Aware Solidification Potts Model

Critical influences of particle size and adhesion on the powder layer uniformity in metal additive manufacturing

In-situ Characterization and Quantification of Melt Pool Variation under Constant Input Energy Density in Laser Powder Bed Fusion Additive Manufacturing Process

Modeling of Temperature Field Evolution During Multilayered Direct Laser Metal Deposition

A numerical investigation of dimensionless numbers characterizing meltpool morphology of the laser powder bed fusion process

Predicting and correlating melt pool characteristics with processing parameters in IN625 powder bed fusion additive manufacturing

The relationship between the macro- and microstructure and the mechanical properties of selective-laser-melted Ti6Al4V samples under low energy inputs: Simulation and experiment

Formation mechanism of pore defects and surface ripples under different process parameters via laser powder bed fusion by numerical simulation and experimental verification

The development of undercut and bulge on a solidified surface