Abstract:High-energy ball milling represents an efficient process for producing composite powders consisting of ceramic particles dispersed in a metallic matrix. However, collision events, plastic deformations, and cold welding during the milling lead to a flake or block-like shape of the resulting composite powders. Further consolidation of such irregularly shaped powders by powder bed-based additive manufacturing technologies can be challenging because of their low flowability and low bulk density. In this work, different approaches, including milling process parameters (speed, process control agent atmosphere) and post-treatments (mechanical and thermal), are investigated on their suitability to influence the particle shape, especially concerning the roundness of the composite powders consisting of the aluminum alloy AlSi10Mg with 5 vol% SiC and Al2O3 reinforcement. It is found that milling with menthol as a process control agent leads to the finest composite powder compared to other milling parameters, with the lowest particle roundness of 0.39 (initial powders 0.84). No success in rounding the milled composite powder could be achieved through mechanical post-treatment in a planetary ball mill. On the other side, the thermal spraying of, e.g., SiC reinforced AlSi10Mg powder resulted in a 77–82% relative roundness. A remarkable change in the microstructure and the shape of the composite powders could also be observed after heat treatment in tube furnaces at a temperature above the melting point of AlSi10Mg. The best result in terms of improved roundness (relative to around 85%) was obtained for Al2O3 reinforced at 600 °C. A further increase of the temperature to 700 °C resulted in a moderate coarsening of powders with Al2O3 and extensive sintering of powders with SiC, presumably due to a different distribution inside the matrix.

PRODUCTION OF SPHERICAL GRANULES OF A HIGH-TEMPERATURE METAL COMPOSITE MATERIAL BASED ON MOLYBDENUM

Spheroidization of Molybdenum Powder by Radio Frequency Thermal Plasma

Method of W-Ni-Fe Composite Spherical Powder Production and the Possibility of Its Application in Selective Laser Melting Technology

Segregation of chemical elements in the volume of powder particles during it's treatment as a method for the production of structurally graded powder materials

Centrifugal granulation behavior in metallic powder fabrication by plasma rotating electrode process

Thermal Plasma Spheroidization of High-Nitrogen Stainless Steel Powder Alloys Synthesized by Mechanical Alloying

Enhancing the physical properties of Mo-Cu composites through plasma spheroidized spherical molybdenum powder

Production of Spheroidized Micropowders of W-Ni-Fe Pseudo-Alloy Using Plasma Technology

Development of technology for the production of granular materials with an ultrafine structure from high-strength aluminum alloys

Influencing the Size and Shape of High-Energy Ball Milled Particle Reinforced Aluminum Alloy Powder

Tailoring the Composition and Structure of Nb-, Si-, and B-Doped Mo-Based Composite Materials in the Self-Propagating High-Temperature Synthesis Metallurgy Process

Investigation of spherical powder obtained by plasma spraying of wire from corrosion-resistant steel 03Kh17N10M2

Manufacture of fine AL2O3 granules as catalyst carrier by an extrusion/spheronization method

Ultrafast Synthesis of Nanocrystalline Molybdenum Powder by Thermal Plasma and Its Sintering Behavior

A powder-based approach to semisolid processing of metals for fabrication of die-castings and composites

Study on the RF Inductively Coupled Plasma Spheroidization of Refractory W and W-Ta Alloy Powders

Manufacturing and properties evaluation of Al2O3/ZrO2 granules derived from sodium alginate gelation

INFLUENCE OF METAL POWDER PRODUCTION METHOD ON MICROSTRUCTURE AND FLUIDITY OF MAGNETICALLY ALLOY GRANULATE

In situ synthesis of spherical W Mo alloy powder for additive manufacturing by spray granulation combined with thermal plasma spheroidization

High volume fraction Al2O3/Al composite thixoforging in pseudo-semi-solid state

Heat conductivity of YAG:Nd + Mo ceramic composites obtained by Spark Plasma Sintering