Abstract:In this paper, various thermal management designs are explored for robotic operation in extreme temperature environments, which includes options for component and chip level electronics heating/cooling like TIM's, heat sinks, heat spreader, insulation material, and PCM's. Furthermore, other active/passive thermal management systems are investigated, such as Heat pipes, Loop Heat Pipes (LHP), and Capillary Pump Loop (CPL) developed by NASA, Fuzzy Logic and PID temperature control methods. Some of the thermal management design challenges faced by the heat pipes, LHP, and CPL devices are decrease in the heating/cooling efficiency with abrupt drop in temperatures, costly equipment, high power consumption, and increase in the overall weight of the robot due to several components. With the limited space available inside the robot design, it requires the use of minimal hardware. A Fuzzy Logic temperature controller is considered for the mobile robot to overcome all the aforementioned thermal challenges. A Fuzzy Logic control system is designed and tested in a simulation environment using a flow simulation software; Ansys Fluent, to authenticate its ability to minimize power consumption by controlling the amount of power supplied to the fan/heater based on the current temperature reading from the sensor, a set-point temperature, and if–then based logical rule-base. The heating/cooling simulation setup consists of four heating units located at different locations inside the robot body and two miniature fans. Moreover, three outlets are included on the wall opposite to the fans for the cooling setup. The opening/closing of the outlets is contingent to the temperature inside the robot and will allow the excess heat to escape the robot's body. Based on the internal flow simulation results, the Fuzzy Logic controller setup was able to increase the extreme low temperature of – 40° C to the desired temperature of 8° C in a total time of 80 s and with a maximum power of 10 W for each heating unit and fans rotating at 1800 rpm for air circulation. However, the power output was minimized by the Fuzzy Logic controller as the internal temperature approached closer to the desired temperature. Moreover, an extreme high temperature of 50° C was decreased rapidly to 8° C in a total time of 12 s with the pressure outlet and inner wall temperatures lower than 15° C. However, in a situation where the initial temperature of the pressure outlet and inner wall are the same as the internal air temperature, the electronics can be cooled by the fans through the forced convection method.

Design and development of controller for Thermoelectric cooler system

Design and optimization of digitalization device of temperature control system using PID Ziegler-Nichols control in chemical engineering laboratory

Design of Temperature Testing System in Multi-Parameter Combined Environmental Test

FEA for Steady-State Thermal Performance of PCR Thermal-Cycler Based on Thermoelectric Cooler

Design Optimization of Thermoelectric Cooling Systems for Applications in Electronic Devices

Development of a Cooling System Simulation Model using Thermoelectric Peltier based on Microcontroller

High Efficiency Thermoelectric Temperature Control System With Improved Proportional Integral Differential Algorithm Using Energy Feedback Technique

Temperature Precise Control in Hot Embossing Device

Optimum Control Strategy and Performance Simulation of a Constant Temperature and Humidity Air-conditioning System

Dynamic Model Identification and Temperature Control of a Thermoelectric Cooler

Real-time optimization of thermoelectric coolers' performance based on energy and exergy analysis

A Kind Of Embedded Temperature Controller Based On Self-Turning Pid For Texturing Machine

Design and implementation of a room temperature control system: Microcontroller-based

Thermal management analysis of new liquid cooling of a battery system based on phase change material and thermoelectric cooler

An Intelligent Thermal Management Fuzzy Logic Control System Design and Analysis Using ANSYS Fluent for a Mobile Robotic Platform in Extreme Weather Applications

Numerical Analysis and Design of Thermal Management System for Lithium Ion Battery Pack Using Thermoelectric Coolers

Design of Water Heater Temperature Control System using PID Control

Performance and regression analysis of air-cooled thermoelectric cooling system using response surface methodology and numerical simulation

Design and optimization of a temperature controller with low overshoot, fast respond and high COP based on water-source thermoelectric heat pump

Thermal management of a flexible controlled thermoelectric energy conversion-utilization system using a multi-objective optimization

OPTIMASI TUNING PID TEMPERATURE CONTROL PADA ALAT HEATER 2801E101 DENGAN MENGGUNAKAN HYSYS INTERFACING MATLAB