Abstract:CONSPECTUS: To tackle the foreseen energy crisis and serious environmental problem caused by conventional energy resources, solar cells, or photovoltaics (PV), a technology that can directly convert sunlight to electricity has been considered to be one of the most important and cost-effective clean energy techniques that benefit the environment. So far, silicon-based PVs have dominated the market due to mature fabrication techniques and their relatively good power conversion efficiency (PCE) and excellent stability. In the past decades, metal halide perovskite PVs have been a major direction of current PV research owing to their intriguing optoelectronic performance. The record PCE of perovskite PV cells has unprecedently increased from an original 3.8 to 25.5%. The typical structure of a photovoltaic perovskite is ABX(3), where A refers to a monovalent cation such as methylammonium (MA(+)), cesium (Cs+), or formamidinium (FA(+)); B refers to a divalent cation such as Pb2+ or Sn2+; and X refers to a halide anion. In general, a perovskite PV device consists of an active layer of the perovskite absorber, which is connected by a hole-transporting layer (HTL) and an electron-transporting layer (ETL). In the beginning, the strategies to improve the PCEs mainly focused on developing an effective method to grow a smooth and continuous polycrystalline film. After the improvement of the baseline PCE of the perovskite PVs, various techniques were employed to reduce the defects of perovskite formed at grain boundaries and surfaces, further pushing the PCEs of perovskite PV devices to over 20%. In the meantime, the discovery of suitable and low-cost interfacial materials such as electron-transporting materials and hole-transporting materials has appealed to the attention of the perovskite research community to accelerate the commercialization of the perovskite PVs. In this Account, we start from our efforts to develop facile and effective fabrication strategies to obtain smooth and continuous polycrystalline perovskite thin films, including vapor-assisted and moisture-assisted perovskite crystal growth. The strategies and the in-depth mechanisms of preventing the formation of specific detrimental defects accumulated at grain boundaries or the surface are also portrayed by designing various passivation molecules with certain functional groups, such as carbonyl groups, amine groups, or sulfonic groups. Some systematically designed electron- or hole-transporting materials to improve the charge extraction and collection efficiency in perovskite PV devices are discussed as well. Finally, future perspectives for further enhancing the long-term stability and PCE are proposed to accelerate the commercialization of perovskite PV devices in the next decade.

Unraveling Loss Mechanisms Arising from Energy‐Level Misalignment between Metal Halide Perovskites and Hole Transport Layers

Comprehensive Understanding of Heat-Induced Degradation of Triple-Cation Mixed Halide Perovskite for a Robust Solar Cell

Tailored Key Parameters of Perovskite for High-Performance Photovoltaics

Minimizing Voltage Loss in Efficient All-Inorganic CsPbI2Br Perovskite Solar Cells Through Energy Level Alignment

Efficiency Potential and Voltage Loss of Inorganic CsPbI2Br Perovskite Solar Cells

Alleviating Interfacial Recombination of Heterojunction Electron Transport Layer via Oxygen Vacancy Engineering for Efficient Perovskite Solar Cells over 23%

An intermeshing electron transporting layer for efficient and stable CsPbI2Br perovskite solar cells with open circuit voltage over 1.3 V

Minimizing Voltage Losses via Synergistically Reducing Hetero-Interface Energy Offset for High Efficiency Perovskite Solar Cells

Heterointerface Energetics Regulation Strategy Enabled Efficient Perovskite Solar Cells

Quantifying the Energy Losses in CsPbI 2 Br Perovskite Solar Cells with an Open-Circuit Voltage of up to 1.45 V

Charge extraction via graded doping of hole transport layers gives highly luminescent and stable metal halide perovskite devices

Low non-radiative recombination loss in CsPbI<inf>2</inf>Br perovskite solar cells

Low non-radiative recombination loss in CsPbI<sub>2</sub>Br perovskite solar cells

Metastable interphase induced pre-strain compensation enables efficient and stable perovskite solar cells

Open-circuit and short-circuit loss management in wide-gap perovskite p-i-n solar cells

Unveiling the surface-interface properties of perovskite crystals and pivotal regulation strategies

Mitigating deep-level defects through a self-healing process for highly efficient wide-bandgap inorganic CsPbI3-xBrx perovskite photovoltaics

Role of surface recombination in perovskite solar cells at the interface of HTL/CH3NH3PbI3

Mismatch of Quasi–Fermi Level Splitting and V oc in Perovskite Solar Cells

Surface p-type band bending and energy level alignment minimizes voltage loss in perovskite solar cells