Abstract:Alloying of corrosion-resistant austenitic steels with nitrogen is widely used in production to stabilize austenite and to improve the strength and other properties of the metal. The possibility of alloying titanium-containing steels with nitrogen by introducing nitrogen into the melt is not possible, as it causes formation of the coarse defects in steel during casting and solidification of the metal (twisting of the peel, large nitride inclusions, accumulations of nitrides, etc.). The method of high-temperature gas nitriding can be alternative to liquid-phase nitriding for alloying austenitic titanium-containing chromium-nickel steels with nitrogen in order to increase their strength properties. In this work, we investigated the possibility of increasing the strength characteristics of thin-sheet austenitic corrosion-resistant Cr – Ni – Ti (Kh18N12T type) steel, containing 1.5 % and 3 % of titanium, through the use of solid-phase high-temperature nitriding. The nitriding was carried out at a temperature of 1000 – 1100 °С in an atmosphere of pure nitrogen for 5 or 8 hours. The average mass fraction of nitrogen in the samples after nitriding for 5 hours was 0.6 % and 0.7 % for the steels with 1.5 and 3 % of titanium, respectively, and after nitriding for 8 hours – 0.8 % and 0.9 %. It was shown that high-temperature nitriding followed by annealing provides a significant (by 2 – 3 times) increase in the metal strength characteristics compared with the state before nitriding, but reduces the ductility. Ductility of the steel is restored during final processing. For Kh18N12Т type steel with 1.5 % of titanium, an increase in the yield strength is obtained – by 3.3 times (from 180 to 600 MPa), strength – by 1.8 times (from 540 to 970 MPa), with a relative elongation of 28 %. An additional increase in strength properties was not found for the steel with 3 % titanium. The obtained results show the possibility of obtaining thin-sheet titanium-containing high-nitrogen steel (or products from it, for example, thin-walled pipes) by applying solid-phase high-temperature nitriding.

Effect of ion nitriding by glow discharge on the physical and mechanical properties of the plastically deformed tool steel R6M5

Effect of Ion Nitriding on the Structural and Phase Composition and Mechanical Properties of High-Speed Steel R6M5 after SPD

Effect of Plasma Nitriding Pretreatment on the Mechanical Properties of AlCrSiN-Coated Tool Steels

Influence of the magnetic field at ion nitriding in the glow-discharge on the microhardness of steel AISI 321

Evolution of Microstructure and Hardness of the Nitrided Zone during Plasma Nitriding of High-Alloy Tool Steel

Plasma-assisted nitriding of M2 tool steel: An experimental and theoretical approach

Study of the effect of ion nitriding regimes on the structure and hardness of steel

Ion nitriding of martensitic and austenitic steels after SPD at different temperatures

Complex Deformation–Ion-Plasma Treatment of Steel 08Kh18N10T-Sh

Tribological Studies of Plasma Source Ion Nitrided Low Alloy Tool Steel

A Study on Formation and Growth Mechanism of Nitride Layers During Plasma Nitriding Process of Plastic Injection Mold Steel

Effect of Gas and Ion Plasma Nitriding on the Structure and Properties of Forging Die Inserts

Nanosized precipitates in H13 tool steel low temperature plasma nitriding

The Effect of Efficient High-Dose-Rate Plasma Immersion Ion Implantation on Microstructure and Properties of 8cr4mo4v Steel

Nitriding Effect on the Tribological Performance of CrN-, AlTiN-, and CrN/AlTiN-Coated DIN 1.2367 Hot Work Tool Steel

Diffusion Nitride Coatings for Heat-Resistant Steels

Effects of Nitriding and Thermal Processing on Wear and Corrosion Resistance of Vanadis 8 Steel

Relation between mechanical and tribological properties of plasma nitrided and TiCrN coated YXR-7 tool steel

The Microstructure of Tool Steel after Low Temperature Ion Nitriding

STRUCTURE AND MECHANICAL PROPERTIES OF AUSTENITIC Cr – Ni – Ti STEELS AFTER HIGH-TEMPERATURE NITRIDING

Microstructure–Wear Resistance Relationship of Nitrogen-Containing High-Speed Tool Steel, AISIM41: Non-equilibrium Solidification