Abstract:An IMC with SSVPWM on rectifier side and a BCPWM technique on the inverter side leads to the maximization of the DC‐link voltage, reduction in switching losses and THD of the load voltage. Simulation results confirm the effectiveness of this approach, with real‐time implementation validated using the OPAL‐RT simulator. This article presents a comprehensive investigation into the improved operation of an in‐direct matrix converter (IMC) through the application of improved pulse width modulation (PWM) techniques. Matrix converters (MCs) draw a discontinuous and distorted input current from the AC source, reducing the input power factor and increasing harmonics. The primary objectives of this work are to maximize the DC‐link voltage and improve source current while simultaneously minimizing switching losses and the total harmonic distortion (THD) of the load voltage, thereby improving power quality standards. To achieve these goals, a symmetrical space vector PWM technique (SSVPWM) is employed on the rectifier side, and an improved bus‐clamping PWM technique (BCPWM) is implemented on the inverter side. By strategically controlling the switching patterns, the DC‐link voltage is maximized while adhering to the voltage and current constraints of the switching devices, which improves the input power factor and hence the overall power quality. Additionally, this technique optimizes the operation of the IMC, leads to a reduction of current ripple, and reduces switching losses, thereby leading to higher efficiency. The core principle behind this research lies in the decoupled control of the rectifier and inverter stages, allowing for independent optimization and maximum system performance. By carefully manipulating the modulation indices, the harmonic content in the output voltage is significantly minimized which is vital for applications requiring a high‐quality and low‐distortion power supply. Simulation studies substantiate the efficacy of the independent control approach, showcasing improvements in DC‐link voltage maximization, switching loss reduction, and reduced output voltage THD. Furthermore, the validation of the real‐time implementation of this study was carried out making use of the OPAL‐RT (OP4510) real‐time simulator.

Minimum switching loss pulse width modulation for reduced power conversion loss in reactive power compensators

A General Pulse Width Modulation Method for Zero-Voltage-Switching Active-clamping Three-phase Power Converters: Edge Aligned Pulse Width Modulation (EA-PWM)

Minimum Switching Losses Discontinuous PWM Strategy for Bidirectional Single-Phase AC–DC Converter With Active Power Decoupling Circuit

Study on Direct Power Control of Static Synchronous Compensator Based on Virtual Flux Linkage

Model Predictive Virtual Flux Control Method for Low Switching Loss Performance in Three-Phase AC/DC Pulse-width-Modulated Converters

Synchronous Single Vector Modulation Strategy for Low-Carrier-Ratio High-Power Applications

Loss Reduction in the SVPWM Linear Modulation Region

An SVPWM Method for Parallel Resonant DC-Link Inverter with the Smallest Loss in the Auxiliary Commutation Circuit

Study on SVPWM Technique for the Switching Losses Reduction of Multi-modular Converter

SVPWM‐Based Algorithm for Reduced THD and Switching Losses Under Varying Fundamental Frequency and Load in a VSI

Torque Ripple Suppression Method with Reduced Switching Frequency for Open-Winding PMSM Drives with Common DC Bus.

Zero Sequence Current Suppression Strategy for Open Winding PMSG Fed by Semi-controlled Converter

A simple passive auxiliary circuit for reduction of losses and efficiency enhancement of synchronous buck converter

Loss Distribution Analysis of Three-Level Active Neutral-Point-Clamped (3L-Anpc) Converter with Different Pwm Strategies

An Optimized Hybrid SVPWM Strategy Based on Multiple Division of Active Vector Time (MDAVT)

Single Active Vector Pulse-width Modulation with Improved Harmonic and Dynamic Performance for Low Carrier Ratio Applications

Adaptive control of a single source reduced switch MLI-based DSTATCOM for wind energy conversion system

Switching Characterization and Power Loss Optimization for Modular Multiactive Bridge Converter under Common Phase Shift Control

Modulation Methods for 3L-NPC Converter Power Loss Management in STATCOM Application

Enhancing Performance of In‐Direct Matrix Converter Through Improved PWM Techniques for Reduced Switching Loss and Optimal DC‐Link Voltage

IPMSM Loss Reduction Control Under High-Speed Conditions for Electric Vehicles