Abstract:An IMC with SSVPWM on rectifier side and a BCPWM technique on the inverter side leads to the maximization of the DC‐link voltage, reduction in switching losses and THD of the load voltage. Simulation results confirm the effectiveness of this approach, with real‐time implementation validated using the OPAL‐RT simulator. This article presents a comprehensive investigation into the improved operation of an in‐direct matrix converter (IMC) through the application of improved pulse width modulation (PWM) techniques. Matrix converters (MCs) draw a discontinuous and distorted input current from the AC source, reducing the input power factor and increasing harmonics. The primary objectives of this work are to maximize the DC‐link voltage and improve source current while simultaneously minimizing switching losses and the total harmonic distortion (THD) of the load voltage, thereby improving power quality standards. To achieve these goals, a symmetrical space vector PWM technique (SSVPWM) is employed on the rectifier side, and an improved bus‐clamping PWM technique (BCPWM) is implemented on the inverter side. By strategically controlling the switching patterns, the DC‐link voltage is maximized while adhering to the voltage and current constraints of the switching devices, which improves the input power factor and hence the overall power quality. Additionally, this technique optimizes the operation of the IMC, leads to a reduction of current ripple, and reduces switching losses, thereby leading to higher efficiency. The core principle behind this research lies in the decoupled control of the rectifier and inverter stages, allowing for independent optimization and maximum system performance. By carefully manipulating the modulation indices, the harmonic content in the output voltage is significantly minimized which is vital for applications requiring a high‐quality and low‐distortion power supply. Simulation studies substantiate the efficacy of the independent control approach, showcasing improvements in DC‐link voltage maximization, switching loss reduction, and reduced output voltage THD. Furthermore, the validation of the real‐time implementation of this study was carried out making use of the OPAL‐RT (OP4510) real‐time simulator.

SVPWM‐Based Algorithm for Reduced THD and Switching Losses Under Varying Fundamental Frequency and Load in a VSI

A Modified DPWM with Neutral Point Voltage Balance Capability for Three-Phase Vienna Rectifiers

Segment Reduction-Based Space Vector Pulse Width Modulation for a Three-Phase F-Type Multilevel Inverter with Reduced Harmonics and Switching States

Modified Single-Edge SVPWM Technique to Reduce the Switching Losses and Increase PWM Harmonics Frequency for Three-Phase VSIs

Enhancing Performance of In‐Direct Matrix Converter Through Improved PWM Techniques for Reduced Switching Loss and Optimal DC‐Link Voltage

Synchronous Optimal PWM with Continuous Switching-to-Fundamental Frequency Ratio

Hybrid Svpwm Technique for Reduced Torque Ripple in Permanent Magnet Synchronous Motor

Torque Ripple Suppression Method with Reduced Switching Frequency for Open-Winding PMSM Drives with Common DC Bus.

Modified Synchronized SVPWM Strategies to Reduce CMV for Three-Phase VSIs at Low Switching Frequency

Carrier-Based Variable Frequency PWM Technique for PMSM Drives to Achieve Dispersed Spectrum and Extended Low-Speed Operation Capability

An SVPWM Method for Parallel Resonant DC-Link Inverter with the Smallest Loss in the Auxiliary Commutation Circuit

An Optimized Hybrid SVPWM Strategy Based on Multiple Division of Active Vector Time (MDAVT)

Real-Time Calculation Of Switching Angles Minimizing Thd For Multilevel Inverters With Step Modulation

Advanced Level Shifted Carrier Based Bus Clamping PWM Technique for a 54-Pulse AC-DC Converter Fed MLI Based Induction Motor Drive

Advanced PWM technique for power quality optimization in 5-level CHB inverter systems

An alternate hybrid PWM for uniform thermal sharing in single phase voltage-source inverter

Dead-time Compensation Method for Bus-clamping Modulated Voltage Source Inverter

A Hybrid PWM Scheme for Stator Loss Reduction of Two Parallel Interleaved Inverter-Fed PMSM Drive with a Minimized Switching Loss

A Modified SVPWM Strategy for Reducing PWM Voltage Noise and Balancing Neutral Point Potential

Hybrid Periodic Carrier Frequency Modulation Technique Based on Modified SVPWM to Reduce the PWM Noise

Modified SVPWM Algorithm for Three Level VSI With Synchronized and Symmetrical Waveforms