Abstract:To optimise the benefits of the deep-rolling process in the service life context of treated components, the process application must be investigated. In addition to the reduction in surface roughness and near-surface material strengthening, compressive residual stresses are introduced, which are primarily responsible for the increase in service life for components, especially in the case of high-strength steel materials. A numerical parameter sensitivity analysis is performed in order to investigate the introduced residual stresses in detail. For this purpose, a validated deep-rolling simulation model is used, which replicates the deep rolling of a railway axle made of the high-strength steel material 34CrNiMo6. The model is based on an elastic-plastic Chaboche material model parameterised on uniaxial tensile and LCF test results and validated with residual stress measurements. Using this model as a basis, the effect of the main process parameters deep-rolling force, feed rate, friction coefficient, number of overruns, tool geometry, and shaft geometry on the resulting residual stress state are investigated. The results reveal that the deep-rolling force has the most significant influence on the introduced residual stress state and should therefore be highlighted. In the case of applying a deep-rolling force of more than 10 kN, maximum compressive residual stresses of around − 1000 MPa are introduced, and a strong saturating behaviour is shown. Maximum compensating tensile residual stresses of + 100 MPa occur below the surface. The main influence of the deep-rolling force is the effective depth achieved, which is determined by the depth of the zero crossing. This varies from 1 mm with an applied force of 2 kN to more than 3.5 mm with 20 kN. Furthermore, the results are analysed to conclude suggestions for the process's applicability, and a proposal for an optimised deep-rolling treatment is presented. There multiple deep rolling with decreased deep-rolling forces is used to achieve a comparably optimised residual stress state. In summary, with the presented results, a contribution to a deeper understanding of the deep-rolling process can be achieved; the influence of the most important process parameters on the residual stress in-depth profiles is established; an optimisation proposal is presented; and correlations are found. Thus, the base work for further fatigue strength assessments and the optimisation of the deep-rolling process regarding the increase of service is laid.

State of residual stress induced by cyclic rolling contact loading

Evolution of Residual Stress Based on Curvature Coupling in Multi-Roll Levelling

Spatial Internal Material Load and Residual Stress Distribution Evolution in Synchrotron In Situ Investigations of Deep Rolling

Preliminary Research on Response of GCr15 Bearing Steel under Cyclic Compression

Subsurface propagation of partial ring cracks under rolling contactPart II. Fracture mechanics analysis

Subsurface propagation of partial ring cracks under rolling contact: Part I. Experimental studies

On the effect of microplasticity on crack initiation from subsurface defects in rolling contact fatigue

Residual stresses evolution and process route optimization of TC4 profiled rolled rings incorporating thermal bulging

Rolling Contact Fatigue Life and Spall Propagation of AISI M50, M50NiL, and AISI 52100, Part II: Stress Modeling

Micromechanism of Plastic Accumulation and Damage Initiation in Bearing Steels under Cyclic Shear Deformation: A Molecular Dynamics Study

Experimental investigations to assess surface fatigue failure in rolling contact bearing

The effect of highly elongated micro-contacts on rolling contact stress field

Study of the Plastic Behavior of Rough Bearing Surfaces Using a Half-Space Contact Model and the Fatigue Life Estimation According to the Fatemi–Socie Model

Numerical parameter sensitivity analysis of residual stresses induced by deep rolling for a 34CrNiMo6 steel railway axle

Localised stress and strain distribution in sliding

Effect of spatial hardness distribution in rolling contact fatigue performance of bearing contacts

Micro-mechanical analysis of residual stresses in cohesive-frictional particulate materials under moving surface loads

Analysis of the Influence of Contact Stress on the Fatigue of AD180 High-Carbon Semi-Steel Roll

A study of local microstructure decay in GCr15 due to rolling contact

Residual Stress of Individual Aluminum Grains from Three Dimensional X-Ray Diffraction

Prediction of Work Hardening in Bearing Steels Undergoing Rolling Contact Loading with a Dislocation-Based Model