Abstract:The paper considers the influence of the parameters of the plasma spraying process on the technological characteristics of multilayer coatings based on nickel-chromium, nickel-chromium-aluminum-yttrium materials, oxide ceramics, intended for operation at high temperature and additional dynamic loads. The design of plasma coatings during their application (with subsequent high-energy processing) under such conditions requires a comprehensive solution – both the use of high-quality powder ingredients and the optimization of technological parameters. The plasma process of applying powder materials has been improved to obtain the maximum values of their utilization factors. The technological characteristics that affect the properties of plasma coatings are optimized, namely: the flow rates of the plasma-forming and materials-transporting gases, the flow rate of supplied powder materials, the current and voltage of the electric arc of the plasma torch, the distance from the plasma torch nozzle exit to the substrate. The paper presents the results of studies of the structure of coatings, performed using scanning electron microscopy. Their analysis has made it possible to form general regularities obtained by the action of radiation of compression plasma flows on coatings formed by air plasma. The considered structures are created using the processes of melting, compaction and high-speed cooling of plasma coatings. The main optimization indicators are the maximum local compaction and spillage of the obtained compositions with the absence of defects and destruction from the impact of compression plasma flows. The main effect during the action of radiation of a compression plasma flow on previously formed coatings is thermal. It contributes heating of the near-surface layer. When the coating is exposed to radiation of compression plasma flows, a remelted layer of oxides with a thickness of about 12–15 μm is created, smoothing the relief of the formed surface and creating a network of cracks on the surface, diverging into the depth of the coating. The liquid-phase processes occurring in the molten phase of the near-surface layers after exposure to compression plasma radiation change the structure of the layers and contribute to the modification of their mechanical properties. By smoothing the surface, increasing the density of the surface crystallized layer and minimizing macro-defects – pores or macrocracks – the mechanical characteristics of the coatings increase.

Nano Structured Plasma Spray Coating for Wear and High Temperature Corrosion Resistance Applications

Microstructure, mechanical and tribological properties of high velocity oxy fuel thermal spray coating: A review

Use of plasma spray technology for deposition of high temperature oxidation/corrosion resistant coatings – a review

A Critical Review on Nano structured Coatings for Alumina-Titania (Al2O3-TiO2) Deposited by Air Plasma Spraying Process (APS)

Nanostructured Coatings: Review on Processing Techniques, Corrosion Behaviour and Tribological Performance

Microstructural Charactistics of Plasma Sprayed NiCrBSi Coatings and Their Wear and Corrosion Behaviors

Structure–Property Correlation of Plasma-Sprayed Inconel625-Al2O3 Bimodal Composite Coatings for High-Temperature Oxidation Protection

D. C. Plasma-Sprayed Coatings of Nanostructured Alumina-Titania-Silica

Tribological properties and corrosion behavior of AC-HVAF sprayed nanostructured NiCrCoAlY-TiB2 coatings

Cobalt- and Chromium-Oxide-Based Coatings: Thermally Spraying a Glaze Layer

Developing an Economical Wear and Corrosion Resistant Fe-Based Metallic Glass Composite Coating by Plasma and HVOF Spraying

Plasma-Sprayed Nanodiamond-Reinforced NiCrBSi Composite Coating for Improved Wear and Corrosion Resistance

Plasma Spraying NiCoCrAlY-Cr2O3-AgMo Coatings: Fabrication and Tribological Mechanisms

Thermal Spray Coating Technology – A Review

Multi-Layers Composite Plasma Coatings Based on Oxide Ceramics and M-Croll

Surface modification of coatings based on Ni-Cr-Al by pulsed plasma treatment

Wear behaviour and microstructural characteristics of cold sprayed nickel-alumina coatings on boiler steel

A review on coatings through thermal spraying

Plasma Coatings Based on Self-Fluxing NiCrBSi Alloy with Improved Wear Resistance Properties

Present status and prospects of nanostructured thermal barrier coatings and their performance improvement strategies: A review

Microstructure, mechanical and high temperature tribological behaviour of graphene nanoplatelets reinforced plasma sprayed titanium nitride coating