Abstract:The mechanical strengths of silicon wafers are crucial for the manufacturing yield of integrated circuits (ICs), which have received intensive attention over the years. With reducing the feature size of ICs, the mechanical strengths of silicon wafers become more significant. Actually, the gliding of indentation dislocations on single-crystalline silicon wafers at a given temperature reflects the mechanical strengths of silicon wafers. Since the gliding of indentation dislocations is driven by the residual stress around the indentation, the investigation on the correlation between the residual stress and dislocation gliding is of significance. In this paper, we first use micro-Raman microscopy to characterize the relief of stress around the indentation due to the annealling at 300 or 500 ℃. Then the effect of such a relief-stress on the gliding of indentation dislocations at 700-900 ℃ is investigated. In the case without the prior stress-relief, the indentation dislocations glide to the maximum distance after 2 h annealling at 700-900 ℃. With the prior stress-relief due to the annealling at 300 or 500 ℃, the indentation dislocations can still glide to the maximum distance after 2 h annealling at 900 ℃, however the gliding velocity significantly decreases and the gliding distance is remarkably reduced after 2 h annealling at 700 or 800 ℃. Such a reduction of gliding distance is most significant in the case of 700 ℃ annealling following the stress-relief with the 500 ℃/2 h annealling. Despite the prior stress-relief, as long as the annealing time at 700 or 800 ℃ is sufficiently extended, the indentation dislocations can glide to the maximum distance. In view of the above results, it is believed that the maximum gliding distance of indentation dislocations at a given temperature is independent of the values of residual stress around the indentation provided that the residual stresses are larger than the critical stress for driving the dislocation movement. Nevertheless, the annealing time for achieving the maximum gliding distance at a given temperature should be remarkably extended as the residual stresses around the indentation are relieved.

Ultra-fast annealing to reduce the residual stress in ultra-thin chips using flash light

Analysis of Residual Stresses Induced in the Confined 3D NAND Flash Memory Structure for Process Optimization

Atomic-scale Stress Modulation of Nanolaminate for Micro-Led Encapsulation.

Effect of Prior Stress-Relief on the Gliding of Indentation Dislocations on Silicon Wafers

Transient Scanning Electron Beam Annealing Methods Used to Study Diffusion and Defects in Implanted Silicon

Transmission Electron Microscopy Investigation of the Micro-Defects in Czochralski Silicon

J un 2 01 9 Ultraslow Dynamic Annealing of Neutron-induced Defects in n-type Silicon

High-Speed and Low-Temperature Atmospheric Photo-Annealing of Large-Area Solution-Processed IGZO Thin-Film Transistors by Using Programmable Pulsed Operation of Xenon Flash Lamp

Investigation of impact of floating gate implantation annealing on the characteristics of 4Xnm ETOX NOR-flash memory

Synergistic Thermal and Electron Wind Force-Assisted Annealing for Extremely High-Density Defect Mitigation

Subsurface Damage and Bending Strength Analysis for Ultra-Thin and Flexible Silicon Chips

Low temperature recovery of OFF-state stress induced degradation of AlGaN/GaN high electron mobility transistors

Numerical Study on the Laser Annealing of Silicon Used in Advanced V-NAND Device

Rapid Thermal Annealing under O2 Ambient to Recover the Deterioration by Gamma-Ray Irradiation in a-IGZO TFTs

Surface Engineering of Polycrystalline Silicon for Long-Term Mechanical Stress Endurance Enhancement in Flexible Low-Temperature Poly-Si Thin-Film Transistors.

Impact of Process Sequence and Device Architecture on Mechanical Stress and Electrical Properties of 3-D Nand Flash

Effect of annealing temperature on the optoelectrical synapse behaviors of A-ZnO microtube

Microcracking in On-Chip Interconnect Stacks: FEM Simulation and Concept for Fatigue Test

Apparatus and method for measuring electro-mechanical property and microstructure of nano material in stress condition

A study of radiation damage and heat annealing effect on the irradiated 3T active pixel sensor

Thermal Residual Stress Analysis of Soldering and Lamination Processes for Fabrication of Crystalline Silicon Photovoltaic Modules