Abstract:Highlights • Superplasticity of fine-grained Mg-10Li alloy was studied. • Severe plastic deformation was used to achieve the fine grains. • Its deformation mechanisms for superplastic flow were analyzed. • Deformation mechanism maps were constructed in 2D and 3D. The superplastic behavior and associated deformation mechanisms of a fine-grained Mg-10.1 Li-0.8Al-0.6Zn alloy (LAZ1011) with a grain size of 3.2 μm, primarily composed of the BCC β phase and a small amount of the HCP α phase, were examined in a temperature range of 473 K to 623 K. The microstructural refinement of this alloy was achieved by employing high-ratio differential speed rolling. The best superplasticity was achieved at 523 K and at strain rates of 10 −4 -5 × 10 −4 s −1 , where tensile elongations of 550–600% were obtained. During the heating and holding stage of the tensile samples prior to tensile loading, a significant increase in grain size was observed at temperatures above 573 K. Therefore, it was important to consider this effect when analyzing and understanding the superplastic deformation behavior and mechanisms. In the investigated strain rate range, the superplastic flow at low strain rates was governed by lattice diffusion-controlled grain boundary sliding, while at high strain rates, lattice diffusion-controlled dislocation climb creep was the rate-controlling deformation mechanism. It was concluded that solute drag creep is unlikely to occur. During the late stages of deformation at 523 K, it was observed that grain boundary sliding led to the agglomeration of the α phase, resulting in significant strain hardening. Deformation mechanism maps were constructed for β-Mg-Li alloys in the form of 2D and 3D formats as a function of strain rate, stress, temperature, and grain size, using the constitutive equations for various deformation mechanisms derived based on the data of the current tests.

Mechanisms of High Strain-Rate Superplasticity of Al-14 mass%Ni-14 mass%Mm (Misch Metal) Alloy Produced from Amorphous Powder

Introducing Equiaxed Grains and Texture into Ni-Mn-Ga Alloys by Hot Extrusion for Superplasticity

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Achieving high strain rate superplasticity in an Al-Cu-Li alloy processed by thermo-mechanical processing

Deformation Behavior and Processing Maps of Ni3Al-based Superalloy During Isothermal Hot Compression

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

Superplasticity of a directionally solidified NiAl–Fe(Nb) alloy at high temperature

SUPERPLASTIC BEHAVIOR OF COARSE-GRAINED Al-Mg ALLOY

High Strain Rate Superplasticity in an Al–Mg–Sc–Zr Alloy Processed Via Simple Rolling

Superplasticity of large-grained Ni-Al alloy

Extraordinary superplasticity at low homologous temperature and high strain rate enabled by a multiphase nanocrystalline network

High Strain Rate Superplasticity in Al-Zn-Mg-Based Alloy: Microstructural Design, Deformation Behavior, and Modeling

Superplastic Deformation of a Heat-Resistant Al–Cu–Mg–Ag–Mn Alloy

Superplasticity of fine-grained Mg-10Li alloy prepared by severe plastic deformation and understanding its deformation mechanisms

Superplasticity of 5083 Alloys with Zr and Mn Additions Produced by Reciprocating Extrusion

Low-temperature superplasticity of a Ti-48Al-2.3Cr-0.2Mo (at.%) alloy

On Mechanical Properties and Superplasticity of Mg–15Al–1Zn Alloys Processed by Reciprocating Extrusion

The Deformation Behavior and Microstructure Evolution of a Mn- and Cr-Containing Al-Mg-Si-Cu Alloy During Hot Compression and Subsequent Heat Treatment

Excellent superplasticity and deformation mechanism of Al–Mg–Sc–Zr alloy processed via simple free forging

Superplasticity of A Ti-48al-2.3cr-0.2mo Alloy

Superplastic Deformation of an As-Rolled Al–Cu–Mg–Ag Alloy