Abstract:Laser-based fabrication of metal-halide perovskite mini-modules has recently been demonstrated using nanosecond (ns) laser pulses. However, it still suffers from high-resistance contacts due to remaining PbI2 residues at the bottom of the absorber-opening P2 scribe line. Therefore, in this study, we investigate the effect of shorter picosecond (ps) laser pulses, and thus lower heat input, on the complete removal of perovskite during P2 laser patterning to achieve low series resistances and thus improved electrical performances.Based on a systematic variation of the incident laser fluence and a comprehensive electrical, morphological and compositional analysis of the scribed area, optimal process windows for successful laser-based series interconnection are identified and evidenced by current density-voltage curves. The amount of PbI2 debris at the scribe bottom is reduced by using ps instead of ns pulses, resulting in improved j-V performance due to higher fill factor and lower series resistance. A numerical analysis of the laser-induced depth-dependent temperature profile shows that overcritical heating for both pulse durations induces explosive boiling of the excited volume, but only in the case of ns structuring the melting point of the underlying transparent oxide contact layer is exceeded. The corresponding scribed line morphology shows features of thermally-driven direct ablation (i.e., splashes), whereas ps pulses produce scribe lines with steep walls and delaminated areas, indicating a mechanical stress-assisted lift-off ablation. Accordingly, P2 laser patterning with ps pulses is recommended due to favorable morphological (steep edges) as well as composition-related (less PbI2 residues) scribe line properties.

Optimization of front-contact laser scribing for thin-film silicon solar modules

A Novel Laser Scribing Method Combined with the Thermal Stress Cleaving for the Crystalline Silicon Solar Cell Separation in Mass Production

Direct Ablation of Zno with Uv and Ir Laser for Thin Film Solar Modules

UV Laser Scribing for Perovskite Solar Modules Fabrication, Pros, and Cons

Investigation of Laser Scribing of A-Si:H from the Film Side for Solar Modules Using a UV Laser with Ns Pulses

Laser Processing Optimization for Large-Area Perovskite Solar Modules

Laser Ablation and Ni/Cu Plating Approach for Tunnel Oxide Passivated Contacts Solar Cells with Variate Polysilicon Layer Thickness: Gains and Possibilities in Comparison to Screen Printing

Laser-Scribing Optimization for Sprayed SnO2-Based Perovskite Solar Modules on Flexible Plastic Substrates

Ablation mechanisms of nanosecond and picosecond laser scribing for metal halide perovskite module interconnection – An experimental and numerical analysis

Morphology and topography of perovskite solar cell films ablated and scribed with short and ultrashort laser pulses

Qualitative Damage Assessment of Laser Contact Opening and Microstructural Evolution at the Rear Contact of a Perc Mono Crystalline Si Solar Cell upon Co-Firing with Si Doped Al Paste

Electron Microscopy Characterisation of P3 Lines and Laser Scribing-induced Perovskite Decomposition in Perovskite Solar Modules.

Rear-side Picosecond Laser Ablation of Indium Tin Oxide Micro-Grooves

A 16.10% Efficiency Organic Solar Module with Ultra-Narrow Interconnections Fabricated Via Nanosecond Ultraviolet Laser Processing

Laser Scribing for Perovskite Solar Modules of Long‐Term Stability

Thermal laser separation and high-throughput layer deposition for edge passivation for TOPCon shingle solar cells

One-step P2 scribing of organometal halide perovskite solar cells by picosecond laser of visible wavelength

Indirect Liftoff Mechanism for High‐Throughput, Single‐Source Laser Scribing for Perovskite Solar Modules

Finite element model of femtosecond laser scribing on silicon heterojunction solar cells

Investigation of Thick-Film-Paste Rheology and Film Material for Pattern Transfer Printing (PTP) Technology