Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

Processing and properties of nanophase SiC/Si3N4 composites

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Silicon Carbide–Silicon Nitride Refractory Materials: Part 1 Materials Science and Processing

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Preparation and mechanical behaviors of multiscale SiC nanowires/carbon fiber reinforced silicon oxycarbide ceramic composites

Sintering, Properties and Applications of Silicon Nitride and Sialon Ceramics

Nanocomposite si-c-n coatings

Phase evolution mechanism of SiC-Al-Si composite under flowing nitrogen at 1600 °C

Fabrication, Microstructural Evolution, and Mechanical Properties of SiC/(Hf0.25Ta0.25Zr0.25Nb0.25)C/C Nanocomposites

Advanced Fabrication Method and Mechanical Properties of Silicon Nitride/Boron Nitride Fibrous Monolithic Ceramics

Silicon oxycarbide composites reinforced with silicon nitride and in situ formed silicon carbide.

Issues in nanocomposite ceramic engineering: focus on processing and properties of alumina-based composites

Synthesis and Characterization of Superconducting NbC Nanotubes

Synthesis of SiC-AlN Ceramic Alloy Powder by the Direct Reactions Between the Constituent Elements.

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

The Development of Al_2O_3/SiC Nanocomposites

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Preparation and characteristics of highly porous BN-Si3N4 composite ceramics by combustion synthesis

Boron nitride (BN) and BN based multiple-layer interphase for SiCf/SiC composites: A review

Tribological behaviour of C/C–SiC composites—A review