Abstract:In this study, the recycled Al-Mg-Mn-Fe alloys having different Fe levels (0.1%, 0.5%, and 0.8%) were successfully developed by applying squeeze casting without heat treatment. Optical and scanning electron microscopy, synchrotron X-ray tomography and radiography, X-ray diffraction, and tensile tests combined with thermodynamic calculations were used to study the correlation between the microstructural evolution and mechanical properties. The results showed that for the alloys with an applied pressure of 75 MPa, as the Fe increase from 0.1% to 0.8%, the yield strength (YS), and ultimate tensile strength (UTS) increased from 122 MPa and 244–146 MPa and 289 MPa, and elongation decreased from 34% to 12%. Even though Fe additions increased the volume fraction of Fe-rich intermetallic phases, it significantly increased the UTS and YS. The synchrotron X-ray tomography and deep-etched results both show that the 3D morphology changed from individual Chinese-script to interconnected plate-like. The 3D morphology of 0.8Fe alloy clearly demonstrate that the hole partially or whole penetrated the entire rectangle-shaped Al6(FeMn) phases, which is due to the close-packed plane growth. In-situ synchrotron X-ray radiography results showed the facet growth behaviour of Al6(FeMn) in 0.8Fe alloys during solidification with a long needle-like shape. The size of primary Al6(FeMn) phases decreases, whereas their number increases with increasing cooling rate. Moreover, the applied pressure was beneficial in refining the size of α-Al grains and Fe-rich phases and reducing the volume fraction of pores, thus contributing to the improvement of strength and elongation. The in-situ tensile test results indicated that the crack initiated in the Fe-rich phases and pores, and the slip lines were blocked by the Fe-rich phases resulting in the strengthening of the secondary phases.

Evolution of iron-rich intermetallics and elevated temperature mechanical properties in gravity die cast 2A16 Al alloy

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

Fe-bearing phase formation, microstructure evolution, and mechanical properties of Al-Mg-Si-Fe alloy fabricated by the twin-roll casting process

The Mechanical Properties of Fe-36.5Al and Its Cr or Ti Containing Alloys at Elevated Temperature

Microstructures and mechanical properties of heat-treated Al-5.0Cu-0.5Fe squeeze cast alloys with different Mn/Fe ratio

The Mechanical Property and Electrical Conductivity Evolution of Al–Fe Alloy Between Room Temperature and Elevated Temperature ECAP

Microstructural Evolution and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy During Heat Treatment

Revealing the influence of Fe on Fe-rich phases formation and mechanical properties of cast Al-Mg-Mn-Fe alloys

Revealing the Effect of Iron Content on the Microstructure Evolution, Mechanical Properties and Corrosion Resistance of the A356-T6 Aluminum Alloys

An Insight into the Precipitate Evolution and Mechanical Properties of a Novel High-Performance Cast Al-Li-Cu-Mg-X Alloy

Evolution of Microstructure and Mechanical Properties of As-Cast Al x CrFe 2 Ni 2 High-Entropy Alloys with Al Content

Effect of Iron-Rich Intermetallic and Eutectic Si Accumulation on Al-Si-Mg Alloy

Towards high mechanical performance Al–Cu–Mg–Fe–Ni alloy: influence of composition, solution treatment and aged process on microstructural evolution and mechanical properties

Effect of Heat Treatment and Fe Content on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Cu Alloys

Microstructural Evolution and Mechanical Properties of Cast Al-3li-1.5cu-0.2zr Alloy During Heat Treatment

Microstructures and mechanical properties of a cast Al–Cu–Li alloy during heat treatment procedure

Microstructural Evolutions and Strengthening Mechanism according to the Aging Temperatures of a High Si Cast Aluminum Alloy

The Evolution of Microstructure and Mechanical Properties at Elevated Temperature of Cast Al–Li–Cu–Mg Alloys with Ni Addition

Microstructural evolution of Al2Cu phase and mechanical properties of the large-scale Al alloy components under different consecutive manufacturing processes

Experimental and theoretical study of the microstructure evolution and thermal-physical properties of hypereutectic Al–Fe alloys

Evolution of precipitation and mechanical properties of high-pressure vacuum die- cast AlSi10MgMn alloy in T5 and T6 heat treated states