Abstract:Thermal barrier coatings (TBCs) have low thermal conductivity, effectively reducing the temperature of the metal matrix and improving thermal performance, knock resistance, and combustion performance of the piston. In this study, an off-road high-pressure common-rail diesel engine was chosen as the research object. Combined with the test results of the piston temperature field under the rated power and maximum torque conditions, a finite element simulation model of the thermal barrier coating piston was established. This model enabled the distribution characteristics and variation laws of the temperature field, stress, and deformation of the thermal barrier coating on the piston matrix to be analysed. The results show that the maximum temperature of the TBC piston is 12.2% and 13.73% lower than that of the aluminium alloy piston under the rated power and maximum torque conditions, respectively. The thermal stresses of the TBC piston at the top of the cavity were 25.9% and 26.8% lower than those of the aluminium piston, while the thermo-mechanical coupling stress of the TBC piston was slightly higher than that of the aluminium piston—1.2 MPa and 3.7 MPa in the bottom of the combustion chamber with geometric mutation, respectively. The radial thermal deformation of the TBC piston was 0.067 mm and 0.073 mm lower than that of the aluminium piston, with the radial thermo-mechanical coupling deformation also decreasing by 0.069 mm and 0.075 mm, respectively. The radial thermal deformation of the piston in the direction parallel to the pinhole axis was greater than that in the direction perpendicular to the pinhole axis; the difference in the magnitude of the change results in uneven thermal deformation of the piston.

Microstructural and thermal properties of piston aluminum alloy reinforced by nano-particles

Characterization of High-Cycle Bending Fatigue Behaviors for Piston Aluminum Matrix SiO2 Nano-composites in Comparison with Aluminum–Silicon Alloys

Effect of nano-clay addition and heat-treatment on tensile and stress-controlled low-cycle fatigue behaviors of aluminum-silicon alloy: Effect of nano-clay addition and heat-treatment

Microstructural Evolution and Tensile Properties of Al-Si Piston Alloys during Long-Term Thermal Exposure

Effects of Alloying Elements and Temperature on Thermodynamic State and Microstructure of Piston Aluminum Alloy

Experiment and numerical simulation study of thermal fatigue of an aluminum alloy piston

Impacts of nano-clay particles and heat-treating on out-of-phase thermo-mechanical fatigue characteristics in piston aluminum-silicon alloys

Metallographic study of laser thermal fatigue damage on piston

Sensitivity analysis of mechanical properties and ductile/brittle behaviors in aluminum‐silicon alloy to loading rate and nano‐particles, considering interaction effects

THERMAL STRESS ANALYSIS OF INTEGRATED COMBUSTION ENGINE PISTON USING CAE TOOLS (ALUMINUM SILICON ALLOY, ALUMINUM SILICON ALLOY STEEL)

Research and analysis of a thermal optimisation design method for aluminium alloy pistons in diesel engines

Comparative analysis of phase composition and heat resistance of piston silumin and experimental alloy Al4Cu2Mn0·5Ca0·2Zr (wt. %)

Investigation and Optimization of Tribo-Mechanical Behavior of Squeeze Casted Al-Si Piston Alloy based Metal Matrix Composite using Response Surface Methodology and Neural Network

Design and Thermal Analysis of Diesel Engine Piston

Thermomechanical Fatigue Analysis of Diesel Engine Piston: Finite Element Simulation and Lifetime Prediction Technique

Mechanical Properties as a Function of Casting Process of Aluminum–Silicon Alloy Matrix Composites

Experimental and simulation study on aluminium alloy piston based on thermal barrier coating

Effect of multi-pass friction stir processing on microstructure and mechanical properties of cast Al-7Fe-5Ni alloy

Investigating the thermal stability of nanocrystalline aluminum-lithium alloy by combining different mechanisms: Reinforcing with graphene and alloying with Sr

Towards high mechanical performance Al–Cu–Mg–Fe–Ni alloy: influence of composition, solution treatment and aged process on microstructural evolution and mechanical properties

Assessment of the Tribological Properties of Aluminum Matrix Composites Intended for Cooperation with Piston Rings in Combustion Engines