Abstract:Recently, high-temperature composites reinforced with in-situ phases have been developed as a new class of composites for harsh environments. The behaviour of these composites under sudden heating and cooling conditions is greatly influenced by the type and fraction of components. The aim of this study is to investigate the microstructural properties and mechanical response of iron based composites after thermal shock cycling. The fabrication process involved in-situ powder metallurgy (IPM) sintering of Fe–B4C starting powders. The samples were subjected to thermal shock with a constant temperature differences (ΔT: 600 °C) and varied cycles (N: 1–50). Comparison of microstructural changes and mechanical behaviour before and after thermal shock has been carried out. The boron atoms released from the initial B4C generated diffusion zones in the matrix dominated by iron boride phases (Fe2B/FeB). An effective matrix-reinforcement interface has been created by in-situ powder metallurgy, where boride phases are almost homogeneously distributed in the iron matrix. While the hardness of the composites was significantly developed by the Fe2B/FeB phases, the addition of B4C resulted in a reduction in the coefficient of thermal expansion (CTE). The in-situ phases contributed in the minimisation of the coefficient mismatch by balancing the thermal expansion coefficients between iron and the initial B4C. Under the influence of thermal shock, microcracks and then macrocracks formed on the sample surfaces, increasing in width and depth with thermal cycles. This resulted in accelerated fracture damage under post-thermal loading. Both the impact and flexural strengths of the samples were significantly reduced as the number of thermal cycles increased. Although the 20% B4C reinforced composite provided maximum hardness, it showed poor resistance to thermal loading. The best results for mechanical loads were achieved by the 5% B4C reinforced composite, which showed no cracks even after 50 thermal cycling.

Microstructure and High Temperature Mechanical Property of Fe–Cr–B Based Metal/Ceramic Composite Manufactured by Metal Injection Molding Process

Macro-micro Analysis of Mechanical Properties of Al0.6CoCrFeNi High-Entropy Alloy Particle-Reinforced Al-based Composites

Microstructure and High Temperature Oxidation Property of Fe–Cr–B Based Metal/Ceramic Composite Manufactured by Powder Injection Molding Process

Effect of Hot Isostatic Pressing on Microstructure and Mechanical Property of Nial/Cr(Mo,Hf) Composite

Microstructure, interface and mechanical property of the DS NiAl/Cr(Mo,Hf) composite

Effect of Fe-Cr-B on the Microstructure and Mechanical Properties of a Powder Injection Molding Processed Fe-Cr-B/316L Stainless Steel Matrix Composite

EFFECT OF HOT ISOSTATIC PRESSING ON MECHANICAL PROPERTIES OF Fe41Cr15Mo14C15B6Y2Co7 BMG

Microstructure and Mechanical Properties Determined in Compressive Tests of Quasi-Rapidly Solidified NiAl-Cr(Mo)-Hf Eutectic Alloy after Hot Isostatic Pressure and High Temperature Treatments

Effects of Hip and Heat Treatment on Microstructure and Compressive Properties of Rapidly Solidified Nial-Cr(Mo)-Hf Eutectic Alloy

Microstructure and High-Temperature Mechanical Properties of CrMnFeCoNi/TiAl Composites Prepared by Powder Metallurgy

Microstructural characteristics and mechanical behavior of microwave-assisted sintered ferromagnetic FeCoNi1.5CrCu HEAp/Al matrix composites

Microstructure evolution, phase decomposition and transition of Al0.8Co0.5Cr1.5CuFeNi HEA during high temperature sintering and mechanical properties corresponding to different microstructures

Microstructure and Mechanical Properties of Al6061-31vol.% B4C Composites Prepared by Hot Isostatic Pressing

Effects of in situ composite ceramics on the mechanical properties and microstructure of Fe–Cr–Ni alloys

Enhancing Mechanical Properties and Electrochemical Behavior of Equiatomic FeNiCoCr High-Entropy Alloy through Sintering and Hot Isostatic Pressing for Binder Jet 3D Printing

Effect of (α + Β) Heat Treatment on Microstructure and Mechanical Properties of (tib + TiC)/Ti–B20 Matrix Composite

Mechanism of Carbide Transformation and Its Impact on the Mechanical Properties of Electron Beam Freeform Fabricated TiC-γ'/Ni-Fe-Cr Composite During Aging Treatment

Thermal shock effects on the microstructure and mechanical properties of iron-based composites reinforced by in-situ Fe2B/FeB ceramic phases

Effect of Cr on Microstructure, Mechanical Properties, and Wear Behavior of in Situ 20 Wt.%al2o3/fe-25Al Composites

Microstructure and Properties of Fe–Cr–B–Al Alloy After Heat Treatment

Structure, Thermal and Mechanical Properties of in Situ Al-Based Metal Matrix Composite Reinforced with Al2o3 and Tic Submicron Particles