Abstract:The Yb:fiber based high-power and high-energy ultrafast lasers usually feature central wavelength of 1030 nm instead of the more common one of 1064 nm, thus limiting some potential wavelength-dependent applications. In this work, a hectowatt 1064-nm femtosecond chirped pulse amplification (CPA) system based on double-stage rod-type photonic crystal fiber (PCF) amplifier was demonstrated, with a pulse energy of 212-μJ and a repetition rate of 0.5 MHz. Compared with our previous work [Opt. Express 30(6), 3611, 2022], two key measures were employed. Firstly, a Yb:YAG crystal was intentionally introduced as a spectral filter for avoiding 1030-nm amplified spontaneous emission (ASE) oscillation, which hence improved the signal-to-noise ratio (SNR) by 15 dB. Secondly, an additional stage of rod-type PCF amplifier was adopted for further power scaling, achieving an average power of 127 W. Finally, the pulse was compressed to ∼460 fs, with an average power of 106 W and a compression efficiency of ∼83%. The beam quality factors (M2) were measured to be M2 X = 1.12 and M2 Y = 1.09. To the best of our knowledge, this is the highest pulse energy among 1064-nm hectowatt-level femtosecond lasers, thus providing a high-quality source for wavelength-dependent applications. For example, it can be used as a driver for high-repetition-rate vacuum ultraviolet (VUV) sources about 10.5 eV, with an expected conversion efficiency of up to 1%.

High-energy 100-ns single-frequency all-fiber laser at 1064 nm

Fiber-solid, Hybrid, Single-Frequency Laser (100 W) with a 100 MHz Repetition Rate and 1 Ns Pulse Width from a Spherical Aberration Compensated Four-Stage Nd:YVO4 Amplifier

High-energy single-frequency pulsed fiber MOPA at 1064 nm based on a hybrid active-fiber

Single frequency high-peak-power fiber laser by suppression of SBS

188 W Nanosecond Pulsed Fiber Amplifier at 1064 Nm

700 W single-frequency all-fiber amplifier at 1064 nm with kHz-level spectral linewidth

High Peak-Power Q-Switched All-Fiber Laser with Tunable Ns-Us Pulse Durations and Hz-Mhz Repetition Rates

Old Wavelength, New Performance: Hectowatt 200-μJ-level Femtosecond fiber CPA System at 1064 Nm

All-Fiber High Repetition Rate Short Pulse Generation Around 1030Nm

72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

240 W High-Average-Power Square-Shaped Nanosecond All-Fiber-Integrated Laser with Near Diffraction-Limited Beam Quality

A Sub-Nanosecond Narrow-Linewidth Pulsed Laser Source with Controllable Repetition Rate

112-Μj 180-Fs Pulses at 1-Khz Repetition Rate from Yb-Doped Laser Based on Strictly All-Fiber CPA Structure

Investigations of the High-Power, Single-Frequency, Sub-Microseconds, 1548-nm Fiber Laser Based on the Optical Pulse Modulation

Linearly-polarized single-transverse-mode high-energy multi-ten nanosecond fiber amplifier with 50W average power.

A 102 W High-Power Linearly-Polarized All-Fiber Single-Frequency Laser at 1560 Nm

Nanosecond Pulse Laser Output with Average Power of 761 W and Pulse Energy of 17.5 Mj Based on Domestic Fiber

All-fiber Mode-Locked Gigahertz Femtosecond Laser at 1610 Nm Using a Self-Developed Long-Wavelength Gain Fiber

All-fiber single-mode actively Q-switched laser at 1120 nm.

Compact Frequency-Modulation Q-switched Single-Frequency Fiber Laser at 1083 Nm