Abstract:A novel trapezoidal corrugated perforated fin core is proposed in this study. The porosity of the fin surface, or perforations, is indicated to promote the unusual behavior of increasing the heat transfer coefficient, while reducing the friction factor with respect to its non-perforated counterpart, primarily due to surface transpiration, which leads to better flow mixing and successive boundary layer disturbances. This allows the heat exchanger to be built much more compact with a smaller volume and a front area. To highlight this, the results of the computational simulations for velocity and temperature fields in typical trapezoidal corrugated perforated plate-fin ducts are presented. Constant property, fully or periodically developed laminar airflow [Formula: see text] with Reynolds number [Formula: see text] passing through inter-fin passages, with fins at constant wall temperature T, in which the fin walls have perforations equally spaced along the length of the duct, is considered and a parametric study of the effects of the duct geometry, including the variation of the inclination angle [Formula: see text] of the diverging plane, the aspect ratio of the channel or period length and fin density effects [Formula: see text] and the converging-diverging ratio of the plate [Formula: see text], is performed. The results of the Fanning friction factor and the Nusselt number over the wide range of the Reynolds number, which was treated in this study, show the improved performance. The improvement is assessed quantitatively by the area goodness factor ( j/ f) relative to Re, comparison with simple flat channels. It is seen that increasing φ to [Formula: see text] improves the core performance; As φ increases beyond [Formula: see text], performance starts to decrease. j/ f increases with increasing λ; and λ = 3.6 acts as an inflection point. It is better to have a large λ value for lower Re range and vice versa. As ε increases, the performance increases; so, the highest area goodness factor value occurs at [Formula: see text]. In case 11, with [Formula: see text], [Formula: see text], and [Formula: see text] at Re = 200, compared to the non-perforated channel, the friction factor decreases about 11%, and the area goodness factor increases about 72%. Thus, the area goodness factor of the perforated case reaches 0.37.

Perforated fins effect on the heat transfer rate from a circular tube by using wind tunnel: An experimental view

A Numerical Study on the Air-Side Heat Transfer of Perforated Finned-Tube Heat Exchangers with Large Fin Pitches

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Study on heat transfer and friction characteristics in fin-tube heat exchangers used for electrical machines cooling

Flow and Heat Transfer Analysis of Perforated Fin in Compact Heat Exchanger

Numerical study of heat transfer of laminar air flow in perforated trapezoidal corrugated plate-fin ducts

Flow and Heat Transfer Characteristics of a Double-Tube Structure Internal Finned Tube with Blossom Shape Internal Fins

Effect of Taper and Perforation on Heat Transfer Coefficient of a Passive Horizontal Heat Sink

The Impact of Square Shape Perforations on the Enhanced Heat Transfer from Fins: Experimental and Numerical Study

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Numerical investigation on effects of using segmented and helical tube fins on thermal performance and efficiency of a shell and tube heat exchanger

Numerical Investigation Of Effect Of Tube Shape On Air-Side Heat Transfer And Pressure Drop Characteristics Of A Finned Tube Heat Exchanger

Thermal performance promotion of a novel double-tube heat exchanger by helical fin with perforations

Effect of partially wet-surface condition on the performance of fin-tube heat exchanger

Performance analysis of a heat exchanger having perforated square fins

Convective Heat Transfer and Pressure Drop of New Triangular Perforated Fin

Experimental Investigation on Thermo-Hydraulic Performance of Heat Exchanger Tube with Solid and Perforated Circular Disk Along with Twisted Tape Insert

Complex Turbulent Flow and Heat Transfer Characteristics of Tubes with Internal Longitudinal Plate-Rectangle Fins in EGR Cooler

Experimental and numerical investigation of heat transfer augmentation in heat sinks using perforation technique

Experimental study on single-phase heat transfer performance of internal helically finned tubes covering low Reynolds number in turbulent flow

Experimental Investigation of Flow-Induced Vibrations of the Finned Tubes in a Parallel Triangular Tube Array